Bedienungsanleitung Garmin GHC10 (Seite 21 von 26) (Englisch)

522189

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

Settings

GHC 10 Owner’s Manual 17



1. From the Heading screen, select  > > .

2. Select an option:

• —set the function performed by the rst button on

the remote.

• —set the function performed by the second button

on the remote.

• —set the function performed by the third button on

the remote.

• —disconnect the remote from the device.



‹



On a GHP 10 autopilot system, if you disable the Shadow Drive, you must

set the autopilot to standby () to manually control the helm. Use

caution when disabling the Shadow Drive.

On a GHP 10V autopilot system, if you disable the Shadow Drive, any

adjustment to the helm completely disengages the autopilot.

Although the autopilot is congured for your boat during installation, you

may nd it necessary to adjust it depending on sea conditions.

Select  > > .

• 

™

—enables the device to enter standby mode

automatically when you manually steer the helm, then engages the

heading hold again when you hold a steady course for a few seconds.

The Shadow Drive is not available on sailboats.

• —Shadow Drive is activated when a certain

amount of pressure is placed on the helm. Adjust this setting if the

Shadow Drive is being falsely tripped or not activating properly. If the

autopilot disengages while the helm is steady, decreasing the sensitivity

value can help alleviate unwanted disengaging. If the Shadow Drive does

not disengage the autopilot correctly when you take the helm, increasing

the sensitivity value may help.

 This setting does not apply to a GHP 10V or GHP 12 autopilot

system.

• —adjust the sea state ltering to set the heading

responsiveness. Set sea state ltering to 0% under normal operating

conditions. Increase sea state ltering in choppy conditions at low speeds

to reduce rudder activity and reduce wear on the autopilot system.

• —enable the device to set the drive direction to

forward or reverse from the heading screen when the autopilot is in

standby mode. See page 4 for information about  direction control.

• —(sailboats only) set the xed angle at

which the autopilot performs a tack or gybe maneuver with heading hold

engaged. Select an angle from 1° to 180°.

• —(sailboats only) the autopilot delays steering a tack

or gybe after you initiate the maneuver using the remote or the device.

The delay counts down on the heading screen, and sounds an alarm when

the autopilot begins the tack or gybe. Select a delay from 0 to 15 seconds.

• —(sailboats only) prevents the autopilot from performing

a gybe. The gybe inhibitor does not prevent you from manually

performing a gybe using the helm or step steering.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin GHC10 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin GHC10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info