Bedienungsanleitung Garmin GHP 12 Autopilot System (Seite 9 von 28) (Englisch)

501977

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

GHP12InstallationInstructions 9



To install the CCU, you must mount it to your boat, connect it to the

ECU, connect it to a NMEA 2000 network, and connect it to the alarm

and to the yellow CCU signal wire on the GHC 10.



Before you can mount the CCU, you must select a location and

determine the correct mounting hardware (page 5).

The CCU bracket has two portions, the mounting portion and the

securing portion.

1. Cut out the mounting template provided on page 25.

2. Tape the template to the mounting location.

If you are installing the CCU on a vertical surface, install the

mounting portion of the bracket with an opening

➊

at the bottom.

➊

➋

3. Drill pilot holes at the three mounting locations.

4. Use screws

➋

to secure the mounting portion of the CCU bracket.



1. Connect the CCU/ECU interconnect cable and the NMEA 2000

drop cable to the CCU.

2. Place the CCU in the mounting

portion of the CCU bracket with

the wires hanging straight down

➊

3. Place the securing portion of the

bracket over the ball and snap

it it into the mounting portion

of the bracket, starting with the

two arms

➋

that do not have the

thumbscrew

➌

4. With the cables hanging straight down, connect the arm with the

thumbscrew.

The cables must hang straight down for the CCU to accurately read

your heading.

5. Hand-tighten the thumbscrew until the CCU is held rmly in the

bracket.

Do not overtighten the thumbscrew.



1. Route the connector-terminated end of the CCU/ECU interconnect

cable to the ECU and make the connection.

2. Route the wires from the bare-wire portion of the cable to the CCU/

ECU interconnect cable.

• Route the red and blue wires to the location where you plan to

install the alarm (page 9).

If the cable is not long enough, extend the appropriate wires with

28 AWG (.08 mm

) wire.

• Route the yellow wire to the location where you plan to install

the GHC 10 (page 10).

If the cable is not long enough, extend the yellow wire with 22

AWG (.33 mm

) wire.

3. Cut and tape the remaining bare wires; they are not used.



The alarm audibly alerts you to important GHP 12 events. It must be

installed near the helm station.



Before you can mount the alarm, you must select a mounting location

(page 5).

Secure the alarm with cable ties or other appropriate mounting

hardware (not included).



1. Route the alarm-cable to the bare-wire end of the CCU/ECU

interconnect cable.

If the cable is not long enough, extend the appropriate wires with 28

AWG (.08 mm

) wire.

2. Connect the cables, based on the table below.









White (+) Red (+)

Black (-) Blue (-)

3. Solder and cover all bare-wire connections.

➊

➋

➌

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin GHP 12 Autopilot System Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin GHP 12 Autopilot System

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info