Bedienungsanleitung Garmin GPS12 (Seite 58 von 66) (Englisch)

522226

Zoom out

Zoom in

Vorherige Seite

1/66

Nächste Seite

Messages &

Time Offsets

APPENDIX C

The GPS 12 uses a flashing on-screen message indica-

tor to alert you to important information. Whenever the

message indicator appears, press PAGE to view the mes-

sage page. There are two types of messages: temporary

alerts and condition alerts. Temporary alerts are cleared

from the message page after viewing, while condition

alerts remain until the condition has been resolved. Pay

careful attention to all messages for your own safety.

Active WPT Can’t be Deletd—You have attempted to change the “active to” or “active from”

waypoint. Clear the active route or GOTO before making your changes.

Accuracy has been Degraded—The accuracy of the GPS 12 has been degraded beyond 500

meters due to poor satellite geometry or data quality. You should check other navigational

sources to verify the position indicated.

Already Exists—The name you are entering already exists in the GPS 12’s memory.

Arrival at (orApproaching)—You are one minute away from reaching a destination waypoint

or at the distance specified on the alarms submenu.

Battery Power is Low—Thebatteries are low and should be replaced.

CDI Alarm—You are left or right of course, beyond the limits set on the alarms submenu.

No DGPSPosition—Not enough data is available to compute a DGPS position.

No RTCM Input—

Beacon receiver is improperly connected or baud rates do not match.

Poor GPSCoverage—The GPS 12 cannot acquire the necessary number of satellites to com-

pute a position. Try another location with a clearer view of the sky.

Power Down and Re-init—The GPS 12 is not able to calculate a position due to abnormal

satellite conditions. Turn the unit off and verify the last position shown by other means. Try the

unit again later, possibly in a different location.

PROX Alarm—You have entered the alarm circle for a specific proximity waypoint.

Proximity Overlapped—The alarm circles of two proximity waypoints overlap which could

cause difficulty in monitoring distances to each waypoint.

Proximity Wpt can’t be Deleted—The waypoint you are trying to delete is listed as a proximi-

ty waypoint and must be removed from the list before it can be deleted.

Read Only Mem has Failed—The permanent memory has failed and the unit is not operable.

Received an Invalid WPT—A waypoint was received during upload transfer that has an

invalid identifier.

Receiver has Failed—A failure in receiver hardware has been detected. If this message persists,

do not use the unit and take it to an authorized dealer for repair.

Route is Full—You have attempted to add more than 30 waypoints to a route.

Route is not Empty—You have attempted to copy into a route already in use.

GPS12B 1/13/99 4:29 PM Page 54

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin GPS12 Seite 58

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin GPS12

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info