Bedienungsanleitung Garmin GPSCOM 170 (Seite 79 von 88) (Englisch)

583716

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

Accuracy has been Degraded—The accura-

cy of the receiver has been degraded beyond

500 meters due to poor satellite geometry or

data quality. You should check other naviga-

tional sources to verify the position indicated.

Active Waypoint Can’t Be Deleted—You

have attempted to change the ‘Active To’ or

‘Active From’ waypoint. Clear the active route

or GOTO before making your changes.

Already Exists—The name you are entering

already exists in memory.

Battery Power is Low—The Ni-Cad battery

is low and should be recharged.

Battery Power is too Low to Transmit—

Battery power is too low to allow transmitting.

COM Failed—The VHF com has failed. Take

the unit to an authorized service center.

GPS and COM Turned Off—The GPS and

Com functions are turned off due to low bat-

tery voltage.

Leg Not Smoothed—The upcoming route leg

is too short for smooth waypoint transitions.

Need 2D Altitude—The unit needs altitude

input in order to start and/or continue 2D nav-

igation.

No DGPS Position—Not enough data is

available to compute a DGPS position.

No RTCM Input—

The beacon receiver is

improperly connected or baud rates do not

match.

Oscillator Needs Adjustment—The unit has

detected excessive drift in its internal crystal

oscillator which may result in longer acquisi-

tion time. Take the unit to an authorized ser-

vice center.

Poor GPS Coverage—The unit cannot

acquire the necessary number of satellites to

compute a position. Try another location with

a clearer view of the sky.

Power Down and Re-init—The unit is not

able to calculate a position due to abnormal

satellite conditions. Turn the unit off and veri-

fy the last position shown by other means. Try

the unit again later, possibly in a different loca-

tion.

Read Only Mem has Failed—The perma-

nent memory has failed and the unit is not

operable. Take the unit to an authorized ser-

vice center.

Received an Invalid WPT—A waypoint was

received during upload transfer that has an

invalid identifier.

Route Waypoint Can’t be Deleted—The

waypoint you are trying to delete is part of a

route. Delete the waypoint from the route

before removing it from memory.

Receiver has Failed—A failure in receiver

hardware has been detected. If this message

persists, take the unit to an authorized dealer.

Route is Full—You have attempted to add

more than 30 waypoints to a route.

The GPSCOM 170 uses a flashing on-screen message

indicator to alert you to important information. Whenever the

message indicator appears, press

to view the message

page. There are two types of messages: temporary alerts and

condition alerts. Temporary alerts are cleared from the message

page after viewing, while condition alerts remain until the con-

dition has been resolved. Pay careful attention to all messages

for your own safety.

Messages

APPENDIX E

170 manual pages rev D 9/21/98 9:23 AM Page 74

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin GPSCOM 170 Seite 79

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info