Bedienungsanleitung Garmin GPSMAP 1000 serie (Seite 32 von 60) (Englisch)

657707

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

transducers are installed at a 45-degree angle and down

view transducers are installed at a zero-degree angle.

Sonar Recordings

Recording the Sonar Display

NOTE: Not all models support sonar recording.

Insert a memory card into the card slot.

From a sonar view, select MENU > Sonar Setup > Sonar

Recording > Record Sonar.

15 minutes of sonar recording uses approximately 200 MB of

space of the inserted memory card. You can record sonar

until the card reaches capacity.

Stopping the Sonar Recording

Before you can stop recording sonar, you must begin recording

it (Recording the Sonar Display,

page

24).

From a sonar view, select MENU

> Sonar Setup > Sonar

Recording > Stop Recording

Deleting a Sonar Recording

Insert a memory card into the card slot.

From a sonar view, select MENU >

Sonar Setup > Sonar

Recordings > View Recordings

Select a recording.

Select

Delete.

Playing Sonar Recordings

Before you can play back the sonar recordings, you must

download and install the HomePort

™

application and record

sonar data onto a memory card.

Remove the memory card from the device.

Insert the memory card into a card reader attached to a

computer.

Open the HomePort application.

Select a sonar recording from your device list.

Right-click the sonar recording in the lower pane.

Select

Playback.

Depth and Water Temperature Graphs

If you are using a depth-capable transducer, or are receiving

water depth information over NMEA 0183 or NMEA 2000, you

can view a graphic log of depth readings over time. If you are

using a temperature-capable transducer, or are receiving water

temperature information over NMEA 0183 or NMEA 2000, you

can view a graphic log of temperature readings over time.

The graphs scroll to the left as information is received.

Select

Sonar >

Data Graphs

Radar

WARNING

The marine radar transmits microwave energy that has the

potential to be harmful to humans and animals. Before

beginning radar transmission, verify that the area around the

radar is clear. The radar transmits a beam approximately 12°

above and below a line extending horizontally from the center of

the radar.

When the radar is transmitting, do not look directly at the

antenna at close range; eyes are the most sensitive part of the

body to electromagnetic energy.

When you connect your compatible chartplotter to an optional

Garmin

marine radar, such as a

GMR

™

Fantom

™

radar or a

GMR

24 xHD, you can view more information about your

surroundings.

The radar transmits a narrow beam of microwave energy as it

rotates to a 360° pattern. When the transmitted energy contacts

a target, some of that energy is reflected back to the radar.

Changing the Radar Mode

From a combination screen or SmartMode layout with radar,

select MENU >

Radar Menu > Change Radar

Select a radar mode.

Transmitting Radar Signals

NOTE:

As a safety feature, the radar enters standby mode after

it warms up. This gives you an opportunity to verify the area

around the radar is clear before beginning radar transmission.

With the chartplotter off, connect your radar as described in

the radar installation instructions.

Turn on the chartplotter.

If necessary, the radar warms up and a countdown alerts you

when the radar is ready.

Select

Radar.

Select a radar mode.

A countdown message appears while the radar is starting up.

Select MENU > Transmit Radar.

Stopping the Transmission of Radar Signals

From a radar screen, select MENU

> Radar to Standby

TIP:

Press

Radar to Standby

from any screen to quickly

stop radar transmission.

Setting Up the Timed Transmit Mode

To help conserve power, you can set up time intervals in which

the radar will transmit and not transmit (standby) signal

transmissions.

NOTE:

This feature is not available in dual radar modes.

From a radar screen, select MENU > Radar Options >

Timed Transmit.

Select

Timed Transmit to enable the option.

Select

Stdby Time, enter the time interval between radar

signal transmissions, and select Done.

Select

Transmit Time, enter the duration of each radar

signal transmission, and select Done.

Enabling and Adjusting a Radar No Transmit Zone

You can indicate an area within which the radar scanner does

not transmit signals.

NOTE:

This feature is not available on all radar and chartplotter

models.

From a radar screen, select MENU > Radar Setup >

Installation >

Enable No Transmit Zone

The no-transmit zone is indicated by a shaded area on the

radar screen.

Select Adjust No Transmit Zone > Move No Transmit

Zone.

Select

Angle 1, and select the new location for the first

angle.

Select Angle 2, and select the new location for the second

angle.

Select Done.

Adjusting the Radar Range

The range of the radar signal indicates the length of the pulsed

signal transmitted and received by the radar. As the range

increases, the radar transmits longer pulses in order to reach

distant targets. Closer targets, especially rain and waves, also

reflect the longer pulses, which can add noise to the radar

screen. Viewing information about longer-range targets can also

24 Radar

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin GPSMAP 1000 serie Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin GPSMAP 1000 serie

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info