Bedienungsanleitung Garmin GPSMAP 1200 serie (Seite 2 von 8) (Englisch)

657708

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

The location and viewing angle should be tested before you

install the device. High viewing angles from above and below

the display may result in a poor image.

Bail Mounting the Device

NOTICE

If you are mounting the bracket on fiberglass with screws, it is

recommended to use a countersink bit to drill a clearance

counterbore through only the top gel-coat layer. This will help to

avoid cracking in the gel-coat layer when the screws are

tightened.

Stainless-steel screws may bind when screwed into fiberglass

and overtightened. It is recommended to apply an anti-seize

lubricant on the screws before installing them.

You can use a bail mount bracket (not included) to bail mount

the device on a flat surface.

Using the bail-mount bracket

as a template, mark the pilot

holes.

Drill the pilot holes.

Using appropriate mounting screws (not included), secure the

bail-mount bracket to the mounting surface.

Install the bail-mount knobs

on the sides of the device.

Place the device in the bail-mount bracket and tighten the

bail-mount knobs.

Flush Mounting the Device

NOTICE

Be careful when cutting the hole to flush mount the device.

There is only a small amount of clearance between the case and

the mounting holes, and cutting the hole too large could

compromise the stability of the device after it is mounted.

The included template and hardware can be used to flush mount

the device in your dashboard.

Trim the template, and make sure it fits in the location where

you want to mount the device.

Secure the template to the mounting location.

Using a 14 mm (

in.) drill bit, drill one or more of the holes

inside the corners of the solid line on the template to prepare

the mounting surface for cutting.

Using a jigsaw or a rotary tool, cut the mounting surface

along the inside line on the template.

Place the device in the cutout to test the fit.

If necessary, use a file and sandpaper to refine the size of

the cutout.

Use a pry tool, such as a flat piece of plastic or a screwdriver,

to carefully pry up the corners of the trim caps, slide the pry

tool to the center, and remove the trim caps.

NOTICE

Use a plastic pry tool when possible. Using a metal pry tool

such as a screwdriver can damage the trim caps and the

device.

After the device fits correctly in the cutout, ensure the

mounting holes on the device line up with the larger 6 mm

(

in.) holes on the template.

If the mounting holes on the device do not line up, mark the

new hole locations.

Select an option:

• If you are using a nut plate, drill a 6 mm (

in.) hole in the

larger hole location.

• If you are not using a nut plate, drill 3.2 mm (

in.) holes

in the larger hole locations.

Starting in one corner of the template, place a nut plate

over the larger hole

drilled in the previous step.

If you are using a nut plate, the smaller hole

on the nut

plate should line up with the smaller hole on the template.

If the smaller hole on the nut plate does not line up with the

smaller hole on the template, mark the new hole location.

If you are using a nut plate, drill a 3.6 mm (

in.) hole in the

smaller hole location.

Repeat to verify placement of the remaining nut plates and

holes on the template.

Remove the template from the mounting surface.

Starting in one corner of the mounting location, place a nut

plate

on the back of the mounting surface, lining up the

large and small holes.

The raised portion of the nut plate should fit into the larger

hole.

Secure the nut plates to the mounting surface by fastening

the included M3 screws

through the smaller 3.6 mm

(

in.) holes.

Install the foam gasket

on the back of the device.

The pieces of the foam gasket have adhesive on the back.

Make sure you remove the protective liner before installing

them on the device.

If you will not have access to the back of the device after you

mount it, connect all necessary cables to the device before

placing it into the cutout.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin GPSMAP 1200 serie Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin GPSMAP 1200 serie

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info