Bedienungsanleitung Garmin GPSMAP 7400 series (Seite 37 von 62) (Englisch)

657692

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

Appearance: Sets the color scheme, look-ahead speed, and

navigation appearance.

Installation: Allows you to configure the radar for the

installation, such as setting the front of the boat and the

antenna park position.

Radar Appearance Settings

From a radar screen, select Menu > Radar Setup >

Appearance.

NOTE:

These settings do not apply to the radar overlay.

Bkgd. Color: Sets the color for the background.

Foreground Clr.: Sets the color scheme for the radar returns.

Look-Ahead Speed: Shifts your present location toward the

bottom of the screen automatically as your speed increases.

Enter your top speed for the best results.

Heading Line: Shows an extension from the bow of the boat in

the direction of travel on the radar screen.

Range Rings: Shows the range rings that help you to visualize

distances on the radar screen.

Bearing Ring: Shows a bearing relative to your heading or

based on a north reference, to help you determine the

bearing to an object shown on the radar screen.

Nav Lines: Shows the navigation lines that indicate the course

you have set using Route To, Auto Guidance, or Go To.

Waypoints: Shows waypoints on the radar screen.

Radar Installation Settings

Front of Boat: Compensates for the physical location of the

radar when it is not on the boat axis (Front-of-Boat Offset,

page 29)

Antenna Configuration: Sets the radar antenna size and sets

the position in which the radar stops (Setting a Custom Park

Position,

page

29)

Enable No Transmit Zone: Sets the area in which the radar

does not transmit signals (Enabling and Adjusting a Radar

No Transmit Zone, page 25)

Front-of-Boat Offset

The front-of-boat offset compensates for the physical location of

the radar scanner on a boat, if the radar scanner does not align

with the bow-stern axis.

Measuring the Potential Front-of-Boat Offset

The front-of-boat offset compensates for the physical location of

the radar scanner on a boat, if the radar scanner does not align

with the bow-stern axis.

Using a magnetic compass, take an optical bearing of a

stationary target located within viewable range.

Measure the target bearing on the radar.

If the bearing deviation is more than +/- 1°, set the front-of-

boat offset.

Setting the Front-of-Boat Offset

Before you can set the front-of-boat offset, you must measure

the potential front-of-boat offset.

The front-of-boat offset setting configured for use in one radar

mode is applied to every other radar mode and to the Radar

overlay.

From a Radar screen or the Radar overlay, select Menu >

Radar Setup >

Installation > Front of Boat

Select

Up or Down to adjust the offset.

Setting a Custom Park Position

If you have more than one radar on your boat, you must be

viewing the radar screen for the radar you want to adjust.

By default, the antenna is stopped perpendicular to the pedestal

when it is not spinning. You can adjust this position.

From the radar screen, select Menu > Radar Setup >

Installation > Antenna Configuration > Park Position.

Use the slider bar to adjust the position of the antenna when

stopped, and select Back

Selecting a Different Radar Source

Select an option:

• From a radar screen or the radar overlay, select Menu >

Radar Setup

> Source

• Select Settings > Communications

> Preferred

Sources > Radar

Select the radar source.

Autopilot

WARNING

You can use the autopilot feature only at a station installed next

to a helm, throttle, and helm control device.

You are responsible for the safe and prudent operation of your

vessel. The autopilot is a tool that enhances your capability to

operate your boat. It does not relieve you of the responsibility of

safely operating your boat. Avoid navigational hazards and

never leave the helm unattended.

Always be prepared to promptly regain manual control of your

boat.

Learn to operate the autopilot on calm and hazard-free open

water.

Use caution when operating the autopilot near hazards in the

water, such as docks, pilings, and other boats.

The autopilot system continuously adjusts the steering of your

boat to maintain a constant heading (heading hold). The system

also allows manual steering and several modes of automatic-

steering functions and patterns.

Opening the Autopilot Screen

Before you can open the autopilot screen, you must have a

compatible autopilot installed and configured.

Select A/V, Gauges, Controls > Autopilot.

Autopilot Screen

Actual heading

Intended heading (heading the autopilot is steering toward)

Actual heading (when in standby mode)

Intended heading (when engaged)

Rudder position indicator (This functionality is available only when a

rudder sensor is connected.)

Adjusting the Step Steering Increment

From the Autopilot screen, select Menu > Autopilot Setup >

Step Turn Size.

Select an increment.

Autopilot 29

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin GPSMAP 7400 series Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin GPSMAP 7400 series

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info