Bedienungsanleitung Garmin GPSMAP 7400 series (Seite 41 von 62) (Englisch)

657692

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

Customizing the Engines Shown in Gauges

Before you can customize how the engines are shown in the

gauges, you must manually select the number of engines

(Selecting the Number of Engines Shown in Gauges, page 32).

From the engine gauges screen, select Menu > Installation

> Engine Selection

> Edit Engines

Select

First Engine.

Select the engine to display in the first gauge.

Repeat for the remaining engine bars.

Enabling Status Alarms for Engine Gauges

You can enable the chartplotter to display engine status alarms.

From the engine gauges screen, select Menu > Installation

> Status Alarms >

When an engine alarms is triggered, a gauge status alarm

message appears and the gauge may become red depending

on the type of alarm.

Enabling Some Engine Gauge Status Alarms

From the engine gauges screen, select Menu

> Installation

> Status Alarms > Custom

Select one or more engine gauge alarms to turn on or off.

Setting the Fuel Alarm

Before you can set a fuel level alarm, a compatible fuel flow

sensor must be connected to the chartplotter.

You can set an alarm to sound when the total amount of

remaining onboard fuel reaches the level you specify.

Select Settings

> Alarms > Fuel > Set Total Fuel Onboard

> On

Enter the remaining amount of fuel that triggers the alarm,

and select Done.

Setting the Fuel Capacity of the Vessel

Select Settings > My Vessel > Fuel Capacity.

Enter the combined total capacity of the fuel tanks.

Synchronizing the Fuel Data with the Actual Vessel

Fuel

You can synchronize the fuel levels in the chartplotter with the

actual fuel in the vessel when you add fuel to your vessel.

Select A/V, Gauges, Controls >

Engines > Menu

Select an option:

• After you have filled up all the fuel tanks on the vessel,

select Fill Up All Tanks. The fuel level is reset to

maximum capacity.

• After you have added less than a full tank of fuel, select

Add Fuel to Boat, and enter the amount added.

• To specify the total fuel in the vessel tanks, select

Set

Total Fuel Onboard, and enter the total amount of fuel in

the tanks.

Viewing the Wind Gauges

Before you can view wind information, you must have a wind

sensor connected to the chartplotter.

Select

A/V, Gauges, Controls > Wind.

Configuring the Sailing Wind Gauge

You can configure the sailing wind gauge to show true or

apparent wind speed and angle.

From the wind gauge, select Menu > Sailing Wind Gauge.

Select an option:

• To show true or apparent wind angle, select Needle

, and

select an option.

• To show true or apparent wind speed, select Wind Speed,

and select an option.

Configuring the Speed Source

You can specify whether the vessel speed data displayed on the

gauge and used for wind calculations is based on water speed

or GPS speed.

From the wind gauge, select Menu > Compass Gauge >

Speed Display.

Select an option:

• To calculate the vessel speed based on data from the

water-speed sensor, select Water Speed.

• To calculate the vessel speed based on GPS data, select

GPS Speed

Configuring the Heading Source of the Wind Gauge

You can specify the source of the heading displayed on the wind

gauge. Magnetic heading is the heading data received from a

heading sensor, and GPS heading is calculated by your

chartplotter GPS (course over ground).

From the wind gauge, select Menu > Compass Gauge >

Heading Source.

Select

GPS Hdg. or Magnetic.

NOTE:

When moving at low speeds or when stationary, the

magnetic compass source is more accurate than the GPS

source.

Customizing the Close-Hauled Wind Gauge

You can specify the range of the close-hauled wind gauge for

both the upwind scale and the downwind scale.

From the wind gauge, select Menu > Compass Gauge >

Gauge Type > Close Hauled Gauge.

Select an option:

• To set the maximum and minimum values that appear

when the upwind close-hauled wind gauge appears, select

Change Upwind Scale, and set the angles.

• To set the maximum and minimum values that appear

when the downwind close-hauled wind gauge appears,

select Change Downwind Scale, and set the angles.

• To view true or apparent wind, select Wind, and select an

option.

Viewing Trip Gauges

Trip gauges show information for odometer, speed, time, and

fuel for your present trip.

Select

Info >

Trip & Graphs > Trip

Resetting Trip Gauges

Select Info

> Trip & Graphs > Trip

Select an option:

• To set all the readings for the present trip to zero, select

Reset Trip.

• To set the maximum speed reading to zero, select Reset

Maximum Speed.

• To set the odometer reading to zero, select Reset

Odometer.

• To set all the readings to zero, select Reset All

Viewing Graphs

Before you can view graphs of various environmental changes,

such as temperature, depth, and wind, you must have an

appropriate transducer or sensor connected to the network.

Select

Info >

Trip & Graphs > Graphs

Gauges and Graphs 33

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin GPSMAP 7400 series Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin GPSMAP 7400 series

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info