Bedienungsanleitung Garmin GPSMAP 7416 (Seite 53 von 62) (Englisch)

657694

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

Select

Back.

System Alarms

Alarm Clock: Sets an alarm clock.

Unit Voltage: Sets an alarm to sound when the battery reaches

a specified low voltage.

GPS Accuracy: Sets an alarm to sound when the GPS location

accuracy falls outside the user-defined value.

Sonar Alarm Settings

NOTE: Some settings require external accessories.

Select Settings

> Alarms > Sonar

Shallow Water: Sets an alarm to sound when the depth is less

than the specified value.

Deep Water: Sets an alarm to sound when the depth is greater

than the specified value.

Water Temp.: Sets an alarm to sound when the transducer

reports a temperature that is 2°F (1.1°C) above or below the

specified temperature.

Contour: Sets an alarm to sound when the transducer detects a

suspended target within the specified depth from the surface

of the water and from the bottom.

Fish: Sets an alarm to sound when the device detects a

suspended target.

• sets the alarm to sound when fish of all sizes are

detected.

• sets the alarm to sound only when medium or large

fish are detected.

• sets the alarm to sound only when large fish are

detected.

Setting Weather Alarms

Before you can set weather alarms, you must have a compatible

chartplotter connected to a weather device, such as a GXM

device, and have a valid weather subscription.

Select Settings

> Alarms > Weather

Turn on alarms for specific weather events.

Setting the Fuel Alarm

Before you can set a fuel level alarm, a compatible fuel flow

sensor must be connected to the chartplotter.

You can set an alarm to sound when the total amount of

remaining onboard fuel reaches the level you specify.

Select Settings > Alarms > Fuel >

Set Total Fuel Onboard

> On

Enter the remaining amount of fuel that triggers the alarm,

and select Done

My Vessel Settings

NOTE: Some settings and options require additional charts or

hardware.

Select Settings >

My Vessel

Depth and Anchoring: Allows you to enter information about

the keel (Setting the Keel Offset

, page

17) and the anchor.

Temp. Offset: Allows you to set an offset value to compensate

for the water temperature reading from a NMEA 0183 water-

temperature sensor or a temperature-capable transducer

(Setting the Water Temperature Offset, page 45).

Calibrate Water Speed: Calibrates the speed-sensing

transducer or sensor (Calibrating a Water Speed Device,

page 46).

Fuel Capacity: Sets the combined fuel capacity of all the fuel

tanks on your vessel (Setting the Fuel Capacity of the Vessel,

page 33).

Vessel Type: Enables some chartplotter features based on the

boat type.

CZone™: Sets the digital switching circuits.

System Profiles: Allows you to save your system profile to a

memory card and import system profile settings from a

memory card. This can be helpful for charter or fleet vessels,

and for sharing your setup information with a friend.

Setting the Keel Offset

You can enter a keel offset to compensate the surface reading

for the depth of a keel, making it possible to measure depth from

the bottom of the keel instead of from the transducer location.

Enter a positive number to offset for a keel. You can enter a

negative number to compensate for a large vessel that may

draw several feet of water.

Complete an action, based on the location of the transducer:

• If the transducer is installed at the water line

, measure

the distance from the transducer location to the keel of the

boat. Enter this value in steps 3 and 4 as a positive

number.

• If the transducer is installed at the bottom of the keel

measure the distance from the transducer to the water

line. Enter this value in steps 3 and 4 as a negative

number.

Select Settings > My Vessel > Depth and Anchoring >

Keel Offset.

Select or based on the location of the transducer.

Enter the distance measured in step 1.

Setting the Water Temperature Offset

Before you can set the water temperature offset, you must have

a NMEA 0183 water-temperature sensor or a temperature-

capable transducer to measure water temperature.

The temperature offset compensates for the temperature

reading from a temperature sensor.

Measure the water temperature using the temperature sensor

or temperature-capable transducer that is connected to the

chartplotter.

Measure the water temperature using a different temperature

sensor or a thermometer that is known to be accurate.

Subtract the water temperature measured in step 1 from the

water temperature measured in step 2.

This is the temperature offset. Enter this value in step 5 as a

positive number if the sensor connected to the chartplotter

measures the water temperature as being colder than it

actually is. Enter this value in step 5 as a negative number if

the sensor connected to the chartplotter measures the water

temperature as being warmer than it actually is.

Device Configuration 45

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin GPSMAP 7416 Seite 53

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin GPSMAP 7416

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info