Bedienungsanleitung Garmin GPSMAP 8000 series (Seite 5 von 14) (Englisch)

658524

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

Secure the antenna to the adapter with the included M3 set

screw

With the antenna installed on the pole mount, fill the

remaining gap in the vertical cable slot with a marine sealant

(optional).

Attach the pole to the boat if it is not already attached.

Route the cable away from sources of electronic

interference.

Mounting the Antenna with the Cable Routed Through the

Pole

Before you permanently mount the antenna, you must test the

mounting location for correct operation (Antenna Mounting

Considerations).

Position a standard 1 in. OD, 14 threads per inch, pipe-

threaded pole (not included) in the selected location, and

mark the approximate center of the pole.

Drill a hole using a 19 mm (

in.) drill bit for the cable to

pass through.

Fasten the pole to the boat.

Thread the pole-mount adapter onto the pole.

Do not overtighten the adapter.

Route the cable through the pole and connect it to the

antenna.

Place the antenna on the pole-mount adapter and twist it

clockwise to lock it in place.

Secure the antenna to the adapter with the included M3 set

screw

With the antenna installed on the pole mount, fill the vertical

cable slot

with a marine sealant (optional).

Route the cable away from sources of electronic

interference.

Mounting the Antenna Under the Deck

NOTICE

Before attaching the under-deck mounting bracket to the

surface, verify the included screws will not penetrate the

surface. If the included screws are too long, you must purchase

surface-appropriate screws to complete the installation.

Before you permanently mount the antenna, you must test the

mounting location for correct operation (Antenna Mounting

Considerations).

Because the antenna cannot acquire signals through metal, it

must be mounted under a fiberglass surface only.

Place the adhesive pads

on the under-deck mounting

bracket

Place the antenna in the under-deck mounting bracket.

Adhere the under-deck mounting bracket to the mounting

surface.

Secure the under-deck mounting bracket to the mounting

surface with screws.

Connect the cable to the antenna

Route the cable away from sources of electronic

interference.

Cable and Connection Considerations

NOTICE

A blue rubber seal is included for each DVI port on the device.

This seal must be installed between each DVI port and DVI-

cable connector to avoid damage to the connectors.

• For easer cable routing, the power, NMEA

0183, and

Garmin Marine Network cables are packaged without the

locking rings installed. You should route the cables before

you install the locking rings.

• After connecting a locking ring to a cable, make sure the ring

is securely connected and the o-ring is in place so the power

or data connection remains secure.

• The device should be connected to the same power source

as the card reader. If this is not possible, the devices must

be connected to the same ground.

Station Connection Considerations

This device can be set up in conjunction with other compatible

Garmin devices to work together as a station. When planning

stations on your boat, observe these considerations.

• Devices earlier than the GPSMAP 8000 series and GPSMAP

8500 series cannot be used in a station.

• Although it is not necessary, it is recommended that you

install all of the devices you plan to use in one station near

each other.

• No special connections are necessary to create a station, as

long as all of the devices are connected to the Garmin

Marine Network (Garmin Marine Network Considerations).

• Stations are created and modified using the device software.

See the owner's manual provided with the device for more

information.

Connecting to Power

WARNING

When connecting the power cable, do not remove the in-line

fuse holder. To prevent the possibility of injury or product

damage caused by fire or overheating, the appropriate fuse

must be in place as indicated in the product specifications. In

addition, connecting the power cable without the appropriate

fuse in place will void the product warranty.

Route the power cable to the power source and to the

device.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin GPSMAP 8000 series Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin GPSMAP 8000 series

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info