Bedienungsanleitung Garmin GPSMAP 8012 (Seite 6 von 14) (Englisch)

522262

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

Connect the red wire to the positive (+) battery terminal, and

connect the black wire to the negative (-) battery terminal.

Install the locking ring and o-ring on the end of the power

cable.

Connect the power cable to the device by turning the locking

ring clockwise.

Power Cable Extensions

If necessary, the power cable can be extended using the

appropriate wire gauge for the length of the extension.

Item Description

Fuse

Battery

1.8 m (6 ft.) without extension

Item Description

Splice

• 12 AWG (3.31 mm²) extension wire, up to 4.6 m (15 ft.)

• 10 AWG (5.26 mm²) extension wire, up to 7 m (23 ft.)

• 8 AWG (8.36 mm²) extension wire, up to 11 m (36 ft.)

Fuse

20.3 cm (8 in.)

Battery

20.3 cm (8 in.)

11 m (36 ft.) maximum extension

Additional Grounding Considerations

This device should not need any additional chassis grounding in

most installation situations. If interference is experienced, the

grounding screw on the housing can be used to connect the

device to the water ground of the boat to help avoid the

interference.

Garmin Marine Network Considerations

This device can connect to additional Garmin Marine Network

devices to share data such as radar, sonar, and detailed

mapping. When connecting Garmin Marine Network devices to

this device, observe these considerations.

• A Garmin Marine Network cable must be used for all Garmin

Marine Network connections.

◦ Third-party CAT5 cable and RJ45 connectors must not be

used for Garmin Marine Network connections.

◦ Additional Garmin Marine Network cables and connectors

are available from your Garmin dealer.

• There are four NETWORK ports on the device that each act

as a network switch. Any compatible device can be

connected to any NETWORK port to share data with all

devices on the boat connected by a Garmin Marine Network

cable.

NMEA 2000

Considerations

NOTICE

If you have an existing NMEA 2000 network on your boat, it

should already be connected to power. Do not connect the

NMEA 2000 power cable to an existing NMEA 2000 network,

because only one power source should be connected to a

NMEA 2000 network.

If you are installing a NMEA 2000 power cable, you must

connect it to the boat ignition switch or through another in-line

switch. NMEA 2000 devices will drain your battery if the NMEA

2000 power cable is connected to the battery directly.

This device can connect to a NMEA 2000 network on your boat

to share data from NMEA 2000 compatible devices such as a

GPS antenna or a VHF radio. The included NMEA 2000 cables

and connectors allow you to either connect the device to your

existing NMEA 2000 network or create a basic NMEA 2000

network if needed.

If you are unfamiliar with NMEA 2000, you should read the

“NMEA 2000 Network Fundamentals” chapter of the Technical

Reference for NMEA 2000 Products. You can find this

document using the “Manuals” link on the product page for your

device at www.garmin.com.

The port labeled NMEA 2000 is used to connect the device to a

standard NMEA 2000 network. The ports labeled ENGINE and

HOUSE are reserved for future use and should not be

connected to a standard NMEA 2000 network.

Item Description

NMEA 2000 compatible Garmin device

GPS antenna

Ignition or in-line switch

NMEA 2000 power cable

NMEA 2000 drop cable

12 Vdc power source

NMEA 2000 terminator or backbone cable

NMEA 2000 T-connector

NMEA 2000 terminator or backbone cable

NMEA 0183 Connection Considerations

• The installation instructions provided with your NMEA 0183

compatible device should contain the information you need

to identify the transmitting (Tx) and receiving (Rx) A (+) and

B (-) wires.

• When connecting NMEA 0183 devices with two transmitting

and two receiving wires, it is not necessary for the NMEA

2000 bus and the NMEA 0183 device to connect to a

common ground.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin GPSMAP 8012 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin GPSMAP 8012

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info