Bedienungsanleitung Garmin GPSMAP 8015 (Seite 4 von 14) (Englisch)

522261

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

• The antenna should not be mounted directly in the path of

the radar

• The antenna should be mounted at least 1 m (3 ft.) away

from (preferably above) the path of a radar beam or a VHF

radio antenna

Testing the Mounting Location

Temporarily secure the antenna in the preferred mounting

location and test it for correct operation.

If you experience interference with other electronics, move

the antenna to a different location, and test it again.

Repeat steps 1–2 until you observe full or acceptable signal

strength.

Permanently mount the antenna.

Surface Mounting the Antenna

NOTICE

If you are mounting the bracket on fiberglass with screws, it is

recommended to use a countersink bit to drill a clearance

counterbore through only the top gel-coat layer. This will help to

avoid any cracking in the gel-coat layer when the screws are

tightened.

Stainless-steel screws may bind when screwed into fiberglass

and overtightened. Garmin recommends applying an anti-seize

lubricant to the screws before installing them.

Before you permanently mount the antenna, you must test the

mounting location for correct operation (Antenna Mounting

Considerations).

Using the surface-mount bracket

as your mounting

template, mark the three pilot-hole locations and trace the

cable-hole in the center of the bracket.

Set the surface-mount bracket aside.

Do not drill through the bracket.

Drill the three 3.2 mm (

in.) pilot holes.

Use a 25 mm (1 in.) hole saw to cut the cable hole in the

center.

Place the seal pad

on the bottom of the surface-mount

bracket, aligning the screw holes.

Use the included M4 screws to secure the surface-mount

bracket to the mounting surface.

Route the cable

through the 25 mm (1 in.) hole and

connect it to the antenna.

Verify the large gasket

is in place on the bottom of the

antenna, place the antenna on the surface-mount bracket,

and twist it clockwise to lock it in place.

Secure the antenna to the mounting bracket with the

included M3 set screw

Route the cable away from sources of electronic

interference.

Mounting the Antenna with the Cable Routed Outside the

Pole

Before you permanently mount the antenna, you must test the

mounting location for correct operation (Antenna Mounting

Considerations).

Route the cable through the pole-mount adapter

, and

place the cable in the vertical slot

along the base of the

pole-mount adapter.

Screw the pole-mount adapter onto a standard 1 in. OD, 14

threads per inch, pipe-threaded pole (not included).

Do not overtighten the adapter on the pole.

Connect the cable to the antenna.

Place the antenna on the pole-mount adapter and twist it

clockwise to lock it in place.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin GPSMAP 8015 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin GPSMAP 8015

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info