Bedienungsanleitung Garmin GPSMAP 8412 (Seite 208 von 222) (Englisch)

801321

208

Zoom out

Zoom in

Vorherige Seite

1/222

Nächste Seite

My device will not turn on or keeps turning off

Devices erratically turning off or not turning on could indicate an issue with the power supplied to the device.

Check these items to attempt to troubleshoot the cause of the power issue.

• Make sure the power source is generating power.

You can check this several ways. For example, you can check whether other devices powered by the source

are functioning.

• Check the fuse in the power cable.

The fuse should be located in a holder that is part of the red wire of the power cable. Check that the proper

size fuse is installed. Refer to the label on the cable or the installation instructions for the exact fuse size

needed. Check the fuse to make sure there is still a connection inside of the fuse. You can test the fuse using

a multimeter. If the fuse is good, the multimeter reads 0ohm.

• Check to make sure the device is receiving at least 12Vdc.

To check the voltage, measure the female power and ground sockets of the power cable for DC voltage. If the

voltage is less than 12Vdc, the device will not turn on.

• If the device is receiving enough power but does not turn on, contact Garmin product support.

My device is not creating waypoints in the correct location

You can manually enter a waypoint location to transfer and share data from one device to the next. If you have

manually entered a waypoint using coordinates, and the location of the point does not appear where the point

should be, the map datum and position format of the device may not match the map datum and position format

originally used to mark the waypoint.

Position format is the way in which the GPS receiver's position appears on the screen. This is commonly

displayed as latitude/longitude in degrees and minutes, with options for degrees, minutes and second, degrees

only, or one of several grid formats.

Map datum is a math model which depicts a part of the surface of the earth. Latitude and longitude lines on a

paper map are referenced to a specific map datum.

1Find out which map datum and position format was used when the original waypoint was created.

If the original waypoint was taken from a map, there should be a legend on the map that lists the map datum

and position format used to create that map. Most often this is found near the map key.

2Select Settings > Preferences > Units.

3Select the correct map datum and position format settings.

4Create the waypoint again.

Contacting Garmin Support

• Go to support.garmin.com for help and information, such as product manuals, frequently asked questions,

videos, and customer support.

• In the USA, call 913-397-8200 or 1-800-800-1020.

• In the UK, call 0808 238 0000.

• In Europe, call +44 (0) 870 850 1241.

194 Appendix

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin GPSMAP 8412 Seite 208

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin GPSMAP 8412

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info