Bedienungsanleitung Garmin GPSMAP 8417 MFD (Seite 2 von 8) (Englisch)

658523

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Mounting the Device

NOTICE

Be careful when cutting the hole to flush mount the device.

There is only a small amount of clearance between the case and

the mounting holes, and cutting the hole too large could

compromise the stability of the device after it is mounted.

To avoid potential damage to the powder coating, use only the

included screws to mount the device. Using screws other than

the ones included will void your warranty.

Do not remove the blue, rubber protective bumper until after the

installation is complete. The bumper helps protect the device

from damage during installation.

The included template and hardware can be used to flush mount

the device in your dashboard. There are three options for

hardware based on the mounting surface material.

• You can drill pilot holes and use the included wood screws.

• You can drill holes and use the included nut plates and

machine screws. The nut plates can add stability to a thinner

surface.

• You can punch holes, tap them to M4, and use the included

machine screws.

Trim the template and make sure it fits in the location where

you want to mount the device.

Secure the template to the selected location.

Using a 3.6 mm (

in.) drill bit, drill one or more of the holes

inside the corners of the solid line on the template to prepare

the mounting surface for cutting.

Using a jigsaw or rotary tool, cut the mounting surface along

the inside of the solid line indicated on the template.

Place the device in the cutout to test the fit.

If necessary, use a file and sandpaper to refine the size of

the cutout.

After the device fits correctly in the cutout, ensure the

mounting holes on the device line up with the larger 7.2 mm

(

in.) holes on the template.

If the mounting holes on the device do not line up, mark the

new hole locations.

Based on your mounting surface, drill or punch and tap the

larger holes:

• Drill 3.2 mm (

in.) pilot holes for the included wood

screws, and skip to step 18.

• Drill 7.2 mm (

in.) holes for the included nut plate and

machine screws.

• Punch and tap M4 holes for the included machine screws,

and skip to step 18.

If using the nut plates, starting in one corner of the template,

place a nut plate

over the larger hole

drilled in step 9.

The smaller hole

on the nut plate should line up with the

smaller hole on the template.

If the smaller 3.6 mm (

in.) hole on the nut plate does not

line up with the smaller hole on the template, mark the new

location.

Repeat steps 10 and 11 for each nut plate.

Using a 3.6 mm (

in.) drill bit, drill the smaller holes.

Remove the template from the mounting surface.

Starting in one corner of the mounting location, place a nut

plate

on the back of the mounting surface, lining up the

large and small holes.

The raised portion of the nut plate should fit into the larger

hole.

Secure the nut plate to the mounting surface by fastening an

included M3 screw

through the smaller 3.6 mm (

in.)

hole.

Repeat steps 15 and 16 for each of the nut plates along the

top and bottom of the device.

If you will not have access to the back of the device after you

mount it, connect all necessary cables to the device before

placing it into the cutout.

NOTE: To prevent corrosion of the metal contacts, cover

unused connectors with the attached weather caps.

Place the device into the cutout.

Secure the device to the mounting surface using the included

M4 screws

or wood screws, depending on the mounting

method.

Carefully remove and discard the rubber protective bumper.

Install the decorative bezel by snapping it in place around the

edges of the device.

Connection Considerations

When connecting this device to power and to other Garmin

devices, you should observe these considerations.

• The power and ground connections to the battery must be

checked to make sure they are secured and cannot become

loose.

• For easier routing, the cables may be packaged without the

locking rings installed. The cables should be routed before

the locking rings are installed.

• After installing a locking ring on a cable, you should make

sure the ring is securely connected and the o-ring is in place

so the power or data connection remains secure.

Connecting to Power

WARNING

When connecting the power cable, do not remove the in-line

fuse holder. To prevent the possibility of injury or product

damage caused by fire or overheating, the appropriate fuse

must be in place as indicated in the product specifications. In

addition, connecting the power cable without the appropriate

fuse in place voids the product warranty.

Route the power cable to the power source and to the device.

Connect the red wire to the positive (+) battery terminal, and

connect the black wire to the negative (-) battery terminal.

Install the locking ring and o-ring on the end of the power

cable.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin GPSMAP 8417 MFD Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin GPSMAP 8417 MFD

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info