Bedienungsanleitung Garmin GPSMAP 8417 (Seite 51 von 222) (Englisch)

801323

Zoom out

Zoom in

Vorherige Seite

1/222

Nächste Seite

Heading and Projected Course of Activated AIS Targets

When heading and course over ground information are provided by an activated AIS target, the heading of the

target appears on a chart as a solid line attached to the AIS target symbol. A heading line does not appear on a

3D chart view.

The projected course of an activated AIS target appears as a dashed line on a chart or a 3D chart view. The

length of the projected course line is based on the value of the projected heading setting. If an activated AIS

target is not transmitting speed information, or if the vessel is not moving, a projected course line does not

appear. Changes in the speed, course over ground, or rate of turn information transmitted by the vessel can

impact the calculation of the projected course line.

When course over ground, heading, and rate of turn information are provided by an activated AIS target, the

projected course of the target is calculated based on the course over ground and the rate of turn information.

The direction in which the target is turning, which is also based on the rate of turn information, is indicated by

the direction of the barb at the end of the heading line. The length of the barb does not change.

When course over ground and heading information are provided by an activated AIS target, but rate of turn

information is not provided, the projected course of the target is calculated based on the course over ground

information.

Activating a Target for an AIS Vessel

1From a chart or 3D chart view, select Options > Layers > Other Vessels > AIS > AIS List.

2Select a vessel from the list.

3Select Review and review the target information.

4Select Activate Target.

Viewing Information about a Targeted AIS Vessel

You can view the AIS signal status, MMSI, GPS speed, GPS heading, and other information that is reported about

a targeted AIS vessel.

1From a chart or a 3D chart view, select an AIS vessel.

2Select AIS Vessel.

Deactivating a Target for an AIS Vessel

1From a chart or a 3D chart view, select an AIS vessel.

2Select AIS Vessel > Deactivate.

Showing AIS Vessels on a Chart or 3D Chart View

Before you can use AIS, you must connect the chartplotter to an external AIS device and receive active

transponder signals from other vessels.

You can configure how other vessels appear on a chart or on a 3D chart view. The display range configured

for one chart or one 3D chart view are applied only to that chart or to that 3D chart view. The details, projected

heading, and trails settings configured for one chart or one 3D chart view are applied to all charts and to all 3D

chart views.

1From a chart or 3D chart view, select Options > Layers > Other Vessels > AIS.

2Select an option:

• To show the tracks of AIS vessels, select AIS Trails and adjust the trail length if needed. .

• To indicate the distance from your location in which AIS vessels appear, select Display Range, and select

a distance.

• To show a list of AIS-activated vessels, select AIS List.

Charts and 3D Chart Views 37

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin GPSMAP 8417 Seite 51

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin GPSMAP 8417

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info