Bedienungsanleitung Garmin GPSMAP 8422 MFD (Seite 53 von 62) (Englisch)

658522

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

CZone™: Sets the digital switching circuits.

System Profiles: Allows you to save your system profile to a

memory card and import system profile settings from a

memory card. This can be helpful for charter or fleet vessels,

and for sharing your setup information with a friend.

Setting the Keel Offset

You can enter a keel offset to compensate the surface reading

for the depth of a keel, making it possible to measure depth from

the bottom of the keel instead of from the transducer location.

Enter a positive number to offset for a keel. You can enter a

negative number to compensate for a large vessel that may

draw several feet of water.

Complete an action, based on the location of the transducer:

• If the transducer is installed at the water line

, measure

the distance from the transducer location to the keel of the

boat. Enter this value in steps 3 and 4 as a positive

number.

• If the transducer is installed at the bottom of the keel

measure the distance from the transducer to the water

line. Enter this value in steps 3 and 4 as a negative

number.

Select Settings > My Vessel > Depth and Anchoring >

Keel Offset.

Select or based on the location of the transducer.

Enter the distance measured in step 1.

Setting the Water Temperature Offset

Before you can set the water temperature offset, you must have

a NMEA 0183 water-temperature sensor or a temperature-

capable transducer to measure water temperature.

The temperature offset compensates for the temperature

reading from a temperature sensor.

Measure the water temperature using the temperature sensor

or temperature-capable transducer that is connected to the

chartplotter.

Measure the water temperature using a different temperature

sensor or a thermometer that is known to be accurate.

Subtract the water temperature measured in step 1 from the

water temperature measured in step 2.

This is the temperature offset. Enter this value in step 5 as a

positive number if the sensor connected to the chartplotter

measures the water temperature as being colder than it

actually is. Enter this value in step 5 as a negative number if

the sensor connected to the chartplotter measures the water

temperature as being warmer than it actually is.

Select Settings > My Vessel > Temp. Offset.

Enter the temperature offset calculated in step 3.

Calibrating a Water Speed Device

If you have a speed-sensing transducer connected to the

chartplotter, you can calibrate that speed-sensing device to

improve the accuracy of water-speed data displayed by the

chartplotter.

Select Settings

> My Vessel > Calibrate Water Speed

Follow the on-screen instructions.

If the boat is not moving fast enough or the speed sensor is

not registering a speed, a message appears.

Select OK

, and safely increase the boat speed.

If the message appears again, stop the boat, and ensure the

speed-sensor wheel is not stuck.

If the wheel turns freely, check the cable connections.

If you continue to get the message, contact Garmin product

support.

Other Vessels Settings

When your compatible chartplotter is connected to an AIS

device or VHF radio, you can set up how other vessels are

displayed on the chartplotter.

Select

Settings > Other Vessels.

AIS: Enables and disables AIS signal reception.

DSC: Enables and disables digital selective calling (DSC).

Collision Alarm: Sets the collision alarm (Setting the Safe-Zone

Collision Alarm,

page

7).

AIS-EPIRB Test: Enables test signals from Emergency Position

Indicating Radio Beacons (EPRIB).

AIS-MOB Test: Enables test signals from man overboard (MOB)

devices.

AIS-SART Test: Enables test transmissions from Search and

Rescue Transponders (SART).

Settings that are Synced on the Garmin

Marine Network

The following devices sync certain settings when connected to

the

Garmin Marine Network.

• echoMAP

™

70 series

• GPSMAP

507 series (software version 3.0 or later)

• GPSMAP

701 series (software version 3.0 or later)

• GPSMAP

702 series

• GPSMAP

800 series

• GPSMAP

902 series

• GPSMAP

1000 series

• GPSMAP

1002 series

• GPSMAP

1202 series

• GPSMAP

7400/7600 series

• GPSMAP

8400/8600 series

The following settings are synced, if applicable, to the device.

Alarm Settings (also syncs alarm acknowledgment):

• Arrival

• Anchor Drag

• Off Course

• GPS Accuracy

• Shallow Water

• Deep Water

(Not available in the GPSMAP 8400/8600

series)

• Water Temp.

• Contour

(Not available in echoMAP 70s and GPSMAP

507/701 series)

• Fish

Device Configuration 45

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin GPSMAP 8422 MFD Seite 53

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin GPSMAP 8422 MFD

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info