Bedienungsanleitung Garmin GPSMAP 8424 MFD (Seite 3 von 8) (Englisch)

658280

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Connect the power cable to the device by turning the locking

ring clockwise.

Additional Grounding Consideration

This device should not need additional chassis grounding in

most installation situations. If you experience interference, you

can use the grounding screw on the housing to connect the

device to the water ground of the boat to help avoid the

interference.

Power Cable Extensions

If necessary, the power cable can be extended using the

appropriate wire gauge for the length of the extension.

Item Description

Fuse

Battery

6 ft. (1.8 m) no extension

Item Description

Splice

• 10 AWG (5.26 mm²) extension wire, up to 15 ft. (4.6 m)

• 8 AWG (8.36 mm²) extension wire, up to 23 ft. (7 m)

• 6 AWG (13.29 mm²) extension wire, up to 36 ft. (11 m)

Fuse

8 in. (20.3 cm)

Battery

8 in. (20.3 cm)

36 ft. (11 m) maximum extension

Station Connection Considerations

This device can be set up in conjunction with other compatible

Garmin devices to work together as a station. When planning

stations on your boat, observe these considerations.

• Devices earlier than the GPSMAP 8000 series and GPSMAP

8500 series cannot be used in a station.

• Although it is not necessary, it is recommended that you

install all of the devices you plan to use in one station near

each other.

• No special connections are necessary to create a station, as

long as all of the devices are connected to the Garmin Marine

Network (Garmin Marine Network Considerations,

page 3).

• Stations are created and modified using the device software.

See the owner's manual provided with the device for more

information.

Garmin Marine Network Considerations

NOTICE

A Garmin Power over Ethernet (PoE) Isolation Coupler (P/N

010-10580-10) must be used when connecting any third-party

device, such as a FLIR

camera, to a Garmin Marine Network.

Connecting a PoE device directly to a Garmin Marine Network

chartplotter damages the Garmin chartplotter and may damage

the PoE device. Connecting any third-party device directly to a

Garmin Marine Network chartplotter will cause abnormal

behavior on the Garmin devices, including the devices not

properly turning off or the software becoming inoperable.

This device can connect to additional Garmin Marine Network

devices to share data such as radar, sonar, and detailed

mapping. When connecting Garmin Marine Network devices to

this device, observe these considerations.

• All devices connected to the Garmin Marine Network must be

connected to the same ground.

• A Garmin Marine Network cable must be used for all Garmin

Marine Network connections.

◦ Third-party CAT5 cable and RJ45 connectors must not be

used for Garmin Marine Network connections.

◦ Additional Garmin Marine Network cables and connectors

are available from your Garmin dealer.

• The NETWORK ports on the device each act as a network

switch. Any compatible device can be connected to any

NETWORK port to share data with all devices on the boat

connected by a Garmin Marine Network cable.

NMEA 2000

Considerations

NOTICE

If you are connecting this device to an existing NMEA 2000

network, the NMEA 2000 network should already be connected

to power. Do not connect the NMEA 2000 power cable to an

existing NMEA 2000 network, because only one power source

should be connected to a NMEA 2000 network.

If you are connecting this device to an existing NMEA 2000

network or engine network by another manufacturer, you should

install a NMEA 2000 Power Isolator (010-11580-00) between

the existing network and the Garmin devices.

If you are installing a NMEA 2000 power cable, you must

connect it to the boat ignition switch or through another in-line

switch. NMEA 2000 devices will drain your battery if the NMEA

2000 power cable is connected to the battery directly.

This device can connect to a NMEA 2000 network on your boat

to share data from NMEA 2000 compatible devices such as a

GPS antenna or a VHF radio. The included NMEA 2000 cables

and connectors allow you to connect the device to your existing

NMEA 2000 network. If you do not have an existing NMEA 2000

network you can create a basic one using cables from Garmin.

If you are unfamiliar with NMEA 2000, you should read the

“NMEA 2000 Network Fundamentals” chapter of the Technical

Reference for NMEA 2000 Products. You can find this document

using the “Manuals” link on the product page for your device at

www.garmin.com.

The port labeled NMEA 2000 is used to connect the device to a

standard NMEA 2000 network.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin GPSMAP 8424 MFD Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin GPSMAP 8424 MFD

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info