Bedienungsanleitung Garmin GPSMAP 8500 (Seite 3 von 12) (Englisch)

522256

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Mounting Considerations

NOTICE

If the device is mounted vertically, it is important to install it with

the connectors pointing downward. This will help avoid potential

water retention around the connectors.

This device should be mounted in a location that is not exposed

to extreme temperatures or conditions. The temperature range

for this device is listed in the product specifications. Extended

exposure to temperatures exceeding the specified temperature

range, in storage or operating conditions, may cause device

failure. Extreme-temperature-induced damage and related

consequences are not covered by the warranty.

• The device must be mounted in a location where it will not be

submerged.

• The device must be mounted in a location with adequate

ventilation where it will not be exposed to extreme

temperatures.

• It is best to mount the device horizontally, with the heat sink

facing upward.

• If the device must be mounted vertically, it must be installed

with the connectors pointing downward.

Mounting the Device

After you select a mounting location, determine the mounting

hardware needed for the surface.

Mounting hardware is included with the device, but it may not

be suitable for the mounting surface.

Place the device in the mounting location and mark the

location of the pilot holes.

Drill the appropriate pilot hole for one corner of the device.

Loosely fasten the device to the mounting surface with one

corner and examine the other three pilot-hole marks.

Mark new pilot-hole locations if necessary, and remove the

device from the mounting surface.

Drill the appropriate pilot holes for the other three marks.

Secure the device to the mounting location.

Card Reader Mounting Considerations

NOTICE

This device should be mounted in a location that is not exposed

to extreme temperatures or conditions. The temperature range

for this device is listed in the product specifications. Extended

exposure to temperatures exceeding the specified temperature

range, in storage or operating conditions, may cause device

failure. Extreme-temperature-induced damage and related

consequences are not covered by the warranty.

The card reader can be flush mounted in the dashboard using

the included hardware. When selecting a mounting location,

observe these considerations.

• The card reader should be mounted in an accessible

location. You must be able to access the card reader when

necessary to insert and remove memory cards containing

additional mapping and device updates, and to transfer user

data.

• To avoid interference with a magnetic compass, the device

should not be installed closer to a compass than the

compass-safe distance value listed in the product

specifications.

• The location must allow room for the routing and connection

of the cables.

Mounting the Card Reader

NOTICE

Be careful when cutting the hole to flush mount the device.

There is only a small amount of clearance between the case

and the mounting holes, and cutting the hole too large could

compromise the stability of the device after it is mounted.

If you are mounting the bracket on fiberglass with screws, it is

recommended to use a countersink bit to drill a clearance

counterbore through only the top gel-coat layer. This will help to

avoid any cracking in the gel-coat layer when the screws are

tightened.

The included template and hardware can be used to flush

mount the device at the selected location.

Trim the flush-mount template and make sure it fits in the

location where you want to mount the device.

Remove the protective liner from the back of the template

and adhere it to the location where you want to mount the

device.

Using a ¼ in. (6 mm) drill bit, drill one or more of the holes

inside the corners of the solid line on the template to prepare

the mounting surface for cutting.

Using a jigsaw, cut the mounting surface along the inside of

the solid line indicated on the template.

Place the device in the cutout to test the fit.

If necessary, use a file and sandpaper to refine the size of

the cutout.

After the device

fits correctly in the cutout, make sure that

the mounting holes on the device line up with the pilot holes

on the template.

If the mounting holes on the device do not line up, mark the

new pilot-hole locations.

Using a center punch, indent the pilot holes and drill the

clearance counterbore through the gell-coat layer as advised

in the notice.

Remove the template from the mounting surface.

If you will not have access to the back of the device after you

mount it, connect all necessary cables to the device before

placing it into the cutout.

Place the device into the cutout.

Secure the device to the mounting surface using the included

screws

Install the decorative bezel by snapping it in place around the

edges of the device.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin GPSMAP 8500 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin GPSMAP 8500

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info