Bedienungsanleitung Garmin GPSMAP 8600 serie (Seite 17 von 64) (Englisch)

658282

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Range Rings: Shows and configures the appearance of range

rings, which help you to visualize distances in some chart

views.

Lane Width: Specifies the width of the navigation lane, which is

the magenta line in some chart views that indicates the

course to your destination.

Other Vessels Settings on the Charts and Chart Views

NOTE:

These options require connected accessories, such as

an AIS receiver or VHF radio.

From a chart or a 3D chart view, select

Menu >

Other Vessels

List: Shows a list of AIS and MARPA vessels.

DSC: Shows the DSC list and sets the DSC trails on the chart.

Collision Alarm: Sets the safe-zone collision alarm (Setting the

Safe-Zone Collision Alarm,

page

7).

Display Setup: See Showing AIS and MARPA Vessels on a

Chart or on a 3D Chart View, page 7.

Laylines Settings

To use the laylines features, you must connect a wind sensor to

the chartplotter.

When in sailing mode (Setting the Vessel Type, page 3), you

can display laylines on the navigation chart. Laylines can be

very helpful when racing.

From the navigation chart, select Menu > Sailing

> Laylines

Display: Sets how the laylines and vessel appear on the chart,

and sets the length of the laylines.

Sailing Ang.: Allows you to select how the device calculates

laylines. The

Actual option calculates the laylines using the

measured wind angle from the wind sensor. The Manual

option calculates the laylines using manually entered

windward and leeward angles.

Windward Ang.: Allows you to set a layline based on the

windward sailing angle.

Leeward Ang.: Allows you to set a layline based on the leeward

sailing angle.

Tide Correction: Corrects the laylines based on the tide.

Layline Filter: Filters the layline data based on the time interval

entered. For a smoother layline that filters out some of the

changes in the boat's heading or true wind angle, enter a

higher number. For laylines that display a higher sensitivity to

changes in the boat's heading or true wind angle, enter a

lower number.

Fish Eye 3D Settings

NOTE:

This feature is available with premium charts, in some

areas.

From the Fish Eye 3D chart view, select Menu.

View: Sets the perspective of the 3D chart view.

Tracks: Shows tracks.

Sonar Cone: Shows a cone that indicates the area covered by

the transducer.

Fish Symbols: Shows suspended targets.

Garmin Quickdraw

™

Contours

Mapping

WARNING

The

Garmin Quickdraw Contours mapping feature allows users

to generate maps. Garmin makes no representations about the

accuracy, reliability, completeness or timeliness of the maps

generated by third parties. Any use or reliance on the maps

generated by third parties is at your own risk.

The

Garmin Quickdraw Contours mapping feature allows you to

instantly create maps with contours and depth labels for any

body of water.

When Garmin Quickdraw Contours records data, a colored

circle surrounds the vessel icon. This circle represents the

approximate area of the map that is scanned by each pass.

A green circle indicates good depth and GPS position, and a

speed under 16 km/h (10 mph). A yellow circle indicates good

depth and GPS position, and a speed between 16 and 32 km/h

(10 and 20 mph). A red circle indicates poor depth or GPS

position, and a speed above 32 km/h (20 mph).

You can view Garmin Quickdraw Contours in a combination

screen or as a single view on the map.

The amount of saved data depends on the size of your memory

card, your sonar source, and the speed of your boat as you

record data. You can record longer when you use a single-beam

sonar. It is estimated that you might be able to record about

1,500 hours of data onto a 2 GB memory card.

When you record data on a memory card in your chartplotter,

the new data is added to your existing Garmin Quickdraw

Contours map, and is saved on the memory card. When you

insert a new memory card, the existing data does not transfer

onto the new card.

Mapping a Body of Water Using the Garmin

Quickdraw Contours Feature

Before you can use the Garmin Quickdraw Contours feature,

you must have a supported chartplotter with upgraded software,

sonar depth, your GPS position, and a memory card with free

space.

NOTE:

This feature is not available on all models.

From a chart view, select Menu > Quickdraw Contours >

Start Recording.

When recording is complete, select Stop Recording.

Select Manage

> Name

, and enter a name for the map.

Adding a Label to a Garmin Quickdraw

Contours Map

You can add labels to a Garmin Quickdraw Contours map to

mark hazards or points of interest.

From the Navigation chart, select a location.

Select Add Quickdraw Label.

Enter text for the label, and select Done.

Garmin Quickdraw

Community

The

Garmin Quickdraw Community is a free, public, online

community that enables you to share your Garmin Quickdraw

Contours maps with others. You can also download maps other

users have created.

To access the Garmin Quickdraw Community, sign in to your

Garmin Connect

™

account, and then you can upload and

download maps using a memory card.

Accessing the

Garmin Quickdraw Community

You can access the Garmin Quickdraw Community using

Garmin Connect website.

Garmin Quickdraw

™

Contours Mapping 9

Garmin GPSMAP 8600 serie Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin GPSMAP 8600 serie

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info