Bedienungsanleitung Garmin GPSMAP3005C (Seite 113 von 124) (Englisch)

522240

113

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

GPSMAP 3005C Owner’s Manual 105

APPendIX > MessAges And AlArMs

Messages and Alarms

The GPSMAP 3005C uses an on-screen message system to notify you of events

and alerts you to problems. Press QUIT to acknowledge the message.

Accuracy Alarm—the GPS accuracy has fallen outside of the user-set value.

Alarm Clock—the alarm clock has sounded.

Anchor Drag Alarm—you have drifted out of the specied distance range.

Approaching Turn—you are nearing a turn in a route.

Approaching <Waypoint>—you are a specied distance from a destination

waypoint.

Arrival At <Waypoint>—you have arrived at the destination waypoint.

Battery Alarm—battery voltage has fallen below the value specied in the

Battery eld on the Alarms tab.

Battery Voltage Is Too High

—too much input voltage; the unit will shut off in

10 seconds. Decrease the input voltage to less than 32 volts.

Boat is not Moving Fast Enough to Calibrate—the boat is not moving fast

enough for the speed wheel to provide a valid speed.

Can’t Read User Card—error reading card; remove and reinsert. Contact your

dealer or Garmin Product Support if the problem persists.

Can’t Read Voltages That High, Limited To Top Of Range

—voltage range

must be between 10.0 and 35.0 volts for the GPSMAP 3005C.

Can’t Read Voltages That Low, Limited To Bottom Of Range

—voltage range

must be between 10.0 and 35.0 volts for the GPSMAP 3005C.

Can’t Send Waypoint—the unit cannot transmit the waypoint using the NMEA

WPL sentence. Check the wiring.

Can’t Unlock Maps—the data on the data card is not unlocked for the unit.

Contact your dealer or Garmin Product Support.

Can’t Write User Card—error reading card; remove and reinsert. Contact your

dealer or Garmin Product Support if the problem persists.

Database Error—internal problem with the unit. Contact your dealer or Garmin

Product Support to have the unit serviced.

Deep Water Alarm—the depth has changed by the amount of the Drift Alarm

value.

Directory Item With This MMSI Already Exists—the MMSI number is already

in the DSC directory. Use a different number.

Directory Memory is Full Can’t Create Entry—the DSC directory has reached

the maximum of 100 contacts. Delete unneeded contacts to add new ones.

Distress Call—a DSC distress call has been received. Take appropriate action.

Drift Alarm—the depth has changed by the amount of the Drift Alarm value.

Fish Alarm—shows an icon and beeps (if enabled) when a sh is detected. This

alarm does not show a message banner.

Invalid MMSI—enter a valid MMSI.

Lost Remote GPS Connection

—there is a problem with the GPS antenna

wiring. Check the connections.

Lost Satellite Reception

—the unit has lost satellite signals. Check the antenna

connections or try moving to a location with a clear view of the sky.

NMEA Depth Is Below Transducer—you must enter an appropriate Keel Offset

for the transducer.

No Proximity Waypoints/Routes/Tracks/User Waypoints Found—you

attempted to transfer user data from a data card that does not contain the specied

type of data. Make sure there is data to transfer on data card.

None Found—no data matched the search criteria.

appendIX

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin GPSMAP3005C Seite 113

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info