Bedienungsanleitung Garmin GT34UHD (Seite 1 von 4) (Englisch)

691442

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

GT34UHD TRANSOM/

TROLLING MOUNT

TRANSDUCER

Installation Instructions

Important Safety Information

WARNING

See the Important Safety and Product Information guide in the

chartplotter or fishfinder product box for product warnings and

other important information.

You are responsible for the safe and prudent operation of your

vessel. Sonar is a tool that enhances your awareness of the

water beneath your boat. It does not relieve you of the

responsibility of observing the water around your boat as you

navigate.

CAUTION

Failure to install and maintain this equipment in accordance with

these instructions could result in damage or injury.

Always wear safety goggles, ear protection, and a dust mask

when drilling, cutting, or sanding.

NOTICE

When drilling or cutting, always check what is on the opposite

side of the surface.

To obtain the best performance and to avoid damage to your

boat, you must install the Garmin

device according to these

instructions.

Read all installation instructions before proceeding with the

installation. If you experience difficulty during the installation, go

to support.garmin.com for more information.

Registering Your Device

Help us better support you by completing our online registration

today. Keep the original sales receipt, or a photocopy, in a safe

place.

Go to my.garmin.com.

Software Update

You should update the software when you install this device.

If your Garmin chartplotter has Wi‑Fi

technology, you should

update the software using the ActiveCaptain

™

app on a

compatible Android

™

or Apple

device. If your chartplotter does

not have has Wi‑Fi technology, you should update the software

using a memory card and a Windows

computer.

For more information, go to support.garmin.com.

Tools Needed

• Drill and drill bits

• Number 2 Phillips screwdriver

• Masking tape

• Marine sealant

Mounting Consideration

To ensure peak performance with the lowest noise and

interference, you should route the transducer cable away from

ignition wires, house batteries and wires, trolling motor batteries

and wires, and high-energy wires such as radar, audio amplifier,

and autopilot pump wires.

Preparing the Transducer for Long-Term Exposure to

Water

NOTICE

Do not use acetone or acetone-based products on the

transducer. Acetone damages the plastic transducer housing.

When you install a transducer on a boat that spends a

significant amount of time in the water, you should coat the

transducer and mounting hardware with a water-based anti-

fouling paint to prevent marine growth.

Lightly sand the transducer and mounting hardware with a

fine-grit abrasive pad.

Wipe the transducer and mounting hardware with isopropyl

alcohol.

Apply water-based anti-fouling paint to the transducer and

mounting hardware.

Installing the Transducer on a Transom

Mounting Location Considerations

• The transducer should be mounted parallel to the water line.

• The transducer should be mounted as close to the center of

the boat as possible.

• If your propeller moves clockwise when the boat moves, the

transducer should be mounted on the starboard side.

• If your propeller moves counter-clockwise when the boat

moves, the transducer should be mounted on the port side.

• The transducer should not be mounted behind strakes, struts,

fittings, water intake or discharge ports, or anything that

creates air bubbles or causes the water to become turbulent.

The transducer must be in clean (non-turbulent) water for

optimal performance.

• The transducer should not be mounted in a location where it

might be jarred when launching, hauling, or storing.

• On single-drive boats, the transducer must not be mounted in

the path of the propeller.

The transducer can cause cavitation that can degrade the

performance of the boat and damage the propeller.

• On boats with outboard or inboard/outboard motors, the

transducer should be mounted at least 38 cm (15 in.) from

the propeller.

• On twin-drive boats, the transducer should be mounted

between the drives, if possible.

Assembling the Transducer with a Transom Mount

Bracket

Attach the mount

to the transducer

with the included

star washers

, and screws

Attach the mount to the bracket

with the bolt

, rubber

washer

, flat washer

, and lock nut

April 2018

190-02409-02_0A

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin GT34UHD Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin GT34UHD

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info