Bedienungsanleitung Garmin GTN 650 (Seite 77 von 412) (Englisch)

579857

Zoom out

Zoom in

Vorherige Seite

1/412

Nächste Seite

190-01007-A3 GTN 6XX/7XX AML STC Installation Manual

Rev. 4 Page 2-35

2.4.11 Cable and Wiring Considerations

Wiring should be installed in accordance with AC 43.13-1B Chapter 11, sections 8 through 13. The

following issues should be addressed:

• It should not be possible for the cable harness to be exposed to wire chafing;

• It should not be possible for a cable harness to be exposed to wire chafing in a manner that both

GPS units fail simultaneously;

• The cable harness should not be located near flight control cables, high capacity electrical lines

(e.g. DC electric motor cables) or fuel lines;

• The cable harness should be located in a protected area of the aircraft ( i.e. isolated from engine

rotor burst); and

• Do not route cable near high-energy sources. (i.e. DC motors, high heat sources)

• Wiring which is required to be shielded per the interconnect diagrams in Appendix E must be

shielded.

• Pigtail lengths must be less than 3.0 inches.

• For dual GTN unit installations, care should be taken to ensure separation between wires of

redundant systems to reduce the possibility of loss of navigation due to a single event.

Refer to Sections 3.3 and 3.6.7 for recommended coaxial cable types.

Refer to Appendix E and Appendix F for the appropriate wiring connections to assemble the wiring

connectors.

2.4.11.1 Pressurized Aircraft Considerations

In pressurized aircraft, wiring that penetrates the pressure vessel must be installed in accordance with the

Type Design of the aircraft. Any wires that penetrate the pressure bulkhead must use existing provisions

such as spare pins in the existing bulkhead connectors, or existing sealed wire through holes in

accordance with the aircraft maintenance manual.

Substantiation for additional holes in the pressure vessel is beyond the scope of this manual and would

require additional data from the aircraft manufacturer or other FAA approved data.

2.4.11.2 Coaxial Cable Considerations

When routing coaxial cables, observe the following precautions:

5. All cable routing should be kept as short and as direct as possible.

6. Avoid sharp bends.

7. Avoid routing cables near power sources (e.g., 400 Hz generators, trim motors, etc.) or near

power for fluorescent lighting.

See Section 3.6.6 for more information on the installation of coaxial cable.

2.4.11.3 Marker Beacon Antenna Cable Installation

When routing marker beacon antenna cables, observe the following precautions:

• All cable routing should be kept as short and as direct as possible.

• Avoid sharp bends.

• Avoid routing cables near power sources (e.g., 400 Hz generators, trim motors, etc.) or near

power for fluorescent lighting.

Avoid routing the marker beacon antenna cable near other antenna cables (e.g. ADF, COM, NAV, GS). See

Section 3.6.7 for marker beacon antenna termination technique.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin GTN 650 Seite 77

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info