Bedienungsanleitung Garmin Legacy Hero (Seite 24 von 32) (Englisch)

691067

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Pairing Your Wireless Sensors

The first time you connect a wireless ANT+ or Bluetooth sensor

to your Garmin device, you must pair the device and sensor.

After they are paired, the device connects to the sensor

automatically when you start an activity and the sensor is active

and within range.

TIP: Some ANT+ sensors pair with your device automatically

when you start an activity with the sensor turned on and near

the device.

Move at least 10 m (33 ft.) away from other wireless sensors.

If you are pairing a heart rate monitor, put on the heart rate

monitor.

The heart rate monitor does not send or receive data until

you put it on.

Hold .

Select > Sensors > Add New.

Bring the device within 3 m (10 ft.) of the sensor, and wait

while the device pairs with the sensor.

After the device connects to the sensor, an icon appears at

the top of the screen.

Foot Pod

Your device is compatible with the foot pod. You can use the

foot pod to record pace and distance instead of using GPS when

you are training indoors or when your GPS signal is weak. The

foot pod is on standby and ready to send data (like the heart

rate monitor).

After 30 minutes of inactivity, the foot pod powers off to

conserve the battery. When the battery is low, a message

appears on your device. Approximately five hours of battery life

remain.

Calibrating Your Foot Pod

Before you can calibrate your foot pod, you must pair your

device with the foot pod (Pairing Your Wireless Sensors,

page 20).

Manual calibration is recommended if you know your calibration

factor. If you have calibrated a foot pod with another Garmin

product, you may know your calibration factor.

Hold .

Select > Sensors > Foot Pod > Cal. Factor.

Adjust the calibration factor:

• Increase the calibration factor if your distance is too low.

• Decrease the calibration factor if your distance is too high.

Improving Foot Pod Calibration

Before you can calibrate your device, you must acquire GPS

signals and pair your device with the foot pod (Pairing Your

Wireless Sensors, page 20).

The foot pod is self-calibrating, but you can improve the

accuracy of the speed and distance data with a few outdoor runs

using GPS.

Stand outside for 5 minutes with a clear view of the sky.

Start a running activity.

Run on a track without stopping for 10 minutes.

Stop your activity, and save it.

Based on the recorded data, the foot pod calibration value

changes, if necessary. You should not need to calibrate the

foot pod again unless your running style changes.

Using an Optional Bike Speed or Cadence

Sensor

You can use a compatible bike speed or cadence sensor to

send data to your device.

• Pair the sensor with your device (Pairing Your Wireless

Sensors, page 20).

• Set your wheel size (Calibrating Your Speed Sensor,

page 20).

• Go for a ride (Going for a Ride, page 11).

Calibrating Your Speed Sensor

Before you can calibrate your speed sensor, you must pair your

device with a compatible speed sensor (Pairing Your Wireless

Sensors, page 20).

Manual calibration is optional and can improve accuracy.

Hold .

Select > Sensors > Speed/Cadence > Wheel Size.

Select an option:

• Select Auto to automatically calculate your wheel size and

calibrate your speed sensor.

• Select Manual, and enter your wheel size to manually

calibrate your speed sensor (Wheel Size and

Circumference, page 25).

Club Sensors

Your device is compatible with Approach

CT10 golf club

sensors. You can use paired club sensors to automatically track

your golf shots, including location, distance, and club type. See

the owner's manual for your club sensors for more information.

Situational Awareness

Your Legacy Series device can be used with Varia smart bike

lights and rearview radar to improve situational awareness. See

the owner's manual for your Varia device for more information.

NOTE: You may need to update the Legacy Series software

before pairing Varia devices (Updating the Software Using the

Garmin Connect App, page 21).

tempe

The tempe is an ANT+ wireless temperature sensor. You can

attach the sensor to a secure strap or loop where it is exposed

to ambient air, and therefore, provides a consistent source of

accurate temperature data. You must pair the tempe with your

device to display temperature data from the tempe.

Device Information

Charging the Device

WARNING

This device contains a lithium-ion battery. See the Important

Safety and Product Information guide in the product box for

product warnings and other important information.

NOTICE

To prevent corrosion, thoroughly clean and dry the contacts and

the surrounding area before charging or connecting to a

computer. Refer to the cleaning instructions in the appendix.

Plug the small end of the USB cable into the charging port on

your device.

20 Device Information

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin Legacy Hero Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin Legacy Hero

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info