Bedienungsanleitung Garmin LIVESCOPE XR LVS62 (Seite 2 von 22) (Englisch)

801309

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

Parts Bags

The installation hardware for the transducer is included in labeled bags. As you complete the installation

process, each procedure begins with a reference to the label on the parts bag needed to complete the

procedure. You can use this table to review or verify the parts bags needed for the installation procedures.

NOTE: You should leave all parts in the labeled bags until you are instructed to open a bag in the instructions.

Not all hardware is used for all installation types.

Contains parts needed when installing the perspective mount

Contains parts needed when installing the perspective or shaft mount

Contains parts needed when installing the perspective, shaft, or barrel mount

Contains parts needed when installing the barrel mount

Contains parts needed when installing the shaft mount

Contains the optional low-profile mounting screws

Mounting Considerations

NOTICE

The use of third-party or self-fabricated mounts could lead to transducer damage or loss. Damage or loss

sustained when using a third-party or self-fabricated mount is not covered under warranty.

Using the hardware supplied, you can mount the transducer on your trolling motor in one of three ways.

• Perspective Mount (Installing the Transducer on the Perspective Mode Mount, page5)

◦You can mount the transducer on the trolling motor shaft using the perspective view mount and bracket.

◦When using the perspective view bracket, the transducer can be used for perspective, downward, and

forward views.

• Barrel Mount (Installing the Transducer on a Trolling Motor Barrel, page9)

◦You can mount the transducer on either side of the trolling motor barrel.

◦When mounted on the barrel, the transducer can be used for downward and forward views.

◦When mounted on the barrel, the transducer cannot be used for perspective view.

• Shaft Mount (Installing the Transducer on the Trolling Motor Shaft, page11)

◦You can mount the transducer on either side of the trolling motor shaft.

◦When mounted directly on the shaft, the transducer can be used for downward and forward views.

◦When mounted directly on the shaft, the transducer cannot be used for perspective view.

◦Mounting the transducer directly on the shaft allows a lower-profile installation than using the perspective-

mount bracket.

When planning the installation, you should observe these considerations.

• You must angle the transducer correctly for the selected view to work properly.

• Installing the transducer with the included knobs allows for tool-free transitions between sonar views.

• You can use the included low-profile hardware instead of the knobs for a more permanent transducer view

position.

• You should mount the transducer in a location where it will not be jarred when launching, hauling, or storing.

• You must install the sonar module in a location with adequate ventilation where it will not be exposed to

extreme temperatures.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin LIVESCOPE XR LVS62 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin LIVESCOPE XR LVS62

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info