Bedienungsanleitung Garmin LIVESCOPE XR LVS62 (Seite 15 von 22) (Englisch)

801309

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

Installing the Transducer on a Pole

You can use the included hardware to install the transducer on a pole (not included). Installing the transducer

on a pole is similar to installing the transducer on a trolling motor shaft. If needed, you can refer to the

diagram provided for installing the transducer on a trolling motor shaft when installing the transducer on a pole

(Installing the Transducer on the Trolling Motor Shaft, page11).

NOTE: You can use the included flat bracket for mounting the transducer on a pole.

Labels identifying the parts bags required for this procedure:

NOTICE

You must secure the transducer cable to the pole or other secure location during installation. Damage to the

transducer cable wire or the cable jacket can cause transducer failure.

1Remove the back of the pole-mount bracket and four screws from parts bag .

2Remove the front half of the pole-mount bracket from parts bag .

3If the pole is equal to or less than 25mm (1in.) in diameter, remove the rubber liner from parts bag .

4If the pole is equal to or less than 25mm (1in.) in diameter, wrap the rubber liner around the pole in the

location you want to install the mount.

5Place the pole-mount bracket around the rubber liner on the pole.

6Insert the screws into the pole-mount bracket, and secure them using the M6 hex wrench in parts bag .

7Remove the knob from parts bag .

8Place the transducer against the pole-mount bracket, and secure it using the knob.

NOTE: You can secure the transducer to the mount using the included low-profile hardware instead of the

knob if you do not plan to switch transducer modes frequently during use (Installing the Transducer Using

Low Profile Mounting Hardware, page14).

9Secure the transducer cable to the pole or other secure location, and route the cable to the location of the

sonar module.

Mounting the GLS 10 Black Box Device

NOTICE

If you are mounting the device in fiberglass, when drilling the pilot holes, use a countersink bit to drill a

clearance counterbore through only the top gel-coat layer. This will help to avoid cracking in the gel-coat layer

when the screws are tightened.

NOTE: Screws are included with the device, but they may not be suitable for the mounting surface.

Before you mount the device, you must select a mounting location, and determine what screws and other

mounting hardware are needed for the surface.

1Place the black box device in the mounting location, and mark the location of the pilot holes.

2Drill a pilot hole for one corner of the device.

3Loosely fasten the device to the mounting surface with one corner, and examine the other three pilot-hole

marks.

4Mark new pilot-hole locations if necessary, and remove the device from the mounting surface.

5Drill the remaining pilot holes.

6Secure the device to the mounting location.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin LIVESCOPE XR LVS62 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin LIVESCOPE XR LVS62

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info