Bedienungsanleitung Garmin Pro Trashbreaker (Seite 5 von 10) (Englisch)

657471

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

Wiggle the device to work the contact points through the

dog's coat.

NOTE: The contact points must have contact with the dog's

skin to be effective.

If the strap is too long, cut off the excess, leaving at least

3 in. (8 cm) to spare.

Mark the hole used to fasten the buckle for future reference

(optional).

MURS Radio Interference

If your handheld device experiences interference from another

transmitter, the LED flashes yellow when you press a training

key.

Selecting and Installing the Contact Points

For best results, select the correct contact points based on your

dog's coat.

Select the correct contact point length for your dog's coat

type:

• For dogs with thicker coats, use the longer contact points.

• For dogs with shorter coats, use the shorter contact

points.

If necessary, use the included wrench to remove the contact

points.

Twist the contact points into the collar.

Tighten with the included wrench, but do not overtighten.

When you put the collar on the dog, make sure the contact

points are tight against the neck.

Training Intensities and Methods

You can use several methods to train your dog. The Pro

Trashbreaker system provides 6 stimulation intensity levels,

which increase sequentially from 1 to 6.

Continuous stimulation: Applies stimulation to the dog the

entire time you press the training key, for a maximum of 8

seconds. Your stimulations should typically be much shorter

than 8 seconds.

Tone: Activates an audible tone instead of stimulation. A tone

can be used as either a positive or negative training cue,

depending on your training program.

Choosing the Correct Intensity Level

Set the intensity to the lowest level (Changing the Intensity

Level).

Select a training key.

Observe the dog for a reaction, such as a head shake, neck

movement, or just a change in expression.

Sometimes dogs will vocalize due to the surprise of the

electrical stimulation. If the dog vocalizes more than once,

the intensity level is too high for beginning training.

If there is no reaction, increase the intensity level by one

level until the dog has a slight but recognizable reaction to

the stimulation.

The intensity level that causes a slight but recognizable reaction

is your dog's baseline level for beginning collar training. You do

not need to, and should not, apply this intensity selection test

again.

After you begin training, the dog’s performance guides your

intensity selection. As the dog advances in training, you may

need to change the level depending upon the training situation.

Changing the Intensity Level

You can select a different intensity level for each dog collar

device.

Select a dog collar device (Selecting a Dog Collar Device).

Adjust the intensity dial to increase or decrease the intensity

level.

BarkLimiter

When the dog collar device is active and properly fitted on the

dog, it detects and corrects barks automatically. The dog collar

device starts at the lowest intensity level and increases the

intensity level gradually until the dog stops barking. When the

dog is quiet, the intensity decreases over time.

The status LED flashes briefly when the dog collar device

detects motion or corrects a bark.

Green, amber, or red

flash

Motion was detected, and no correction was

applied.

Blue flash A bark was detected, and a correction was

applied.

NOTE: A green, amber, or red flash denotes how much charge

is left in the dog device battery, ranging from high to low.

Enabling the BarkLimiter Feature

On the dog collar device, hold the power key until the LED

flashes blue.

Bark Odometer™

When you turn off the device, the LED flashes red and green to

report the number of times the device detected a bark since it

was last turned on. This can help you track your dog's barking

behavior.

Red flash 10 barks

Green flash 1 bark

For example, one red flash followed by four green flashes

indicates the device detected 14 barks.

Zero flashes indicates the device detected zero barks.

Checking the Bark Odometer

Remove the device from the dog.

Position the device so that you can see the status LED.

Hold the power key until the status LED turns red, and

release.

Count the red and green flashes.

Using the Light

You can use the light feature on your device to verify pairing,

help locate your dog, and provide safety for your dog at night.

Select a dog collar device (Selecting a Dog Collar Device).

Rotate the intensity dial to L.

Select the training key.

Dog Training 3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin Pro Trashbreaker Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info