Bedienungsanleitung Garmin Sport Pro (Seite 6 von 12) (Englisch)

657472

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Plug the power cable into a power source.

The status LED is solid red when the collar is charging.

After the status LED turns solid green, remove the charging

clip from the collar.

Turning On the Dog Collar Device

• To turn on the dog collar device in training mode, hold the

power key until the status LED turns green and the collar

beeps.

• To turn on the dog collar device in independent BarkLimiter

mode, hold the power key until the status LED turns blue

(Enabling the Independent BarkLimiter Feature from the Dog

Collar Device, page 4).

• To turn on the dog collar device in pairing mode, hold the

power key until the status LED turns yellow (Pairing a Dog

Collar Device with the Handheld Device, page 2).

Turning Off the Device

On the dog collar device, hold the power key until the status

LED turns red.

Release the power key.

The dog collar device beeps to confirm powering off.

NOTE: If the device is powered off in BarkLimiter mode, the

LED flashes the number of corrected barks before powering

off (Bark Odometer

™

, page 4).

Dog Collar Device

You can use up to 3 dog collar devices with a single handheld

device.

Each dog collar device must be paired with the handheld device

before it can be used. During the pairing process, each dog

collar device is associated with a different color on the handheld

device.

Pairing a Dog Collar Device with the Handheld Device

NOTE: If your handheld device and dog collar device were

included in the same package, the devices are paired from the

factory.

On the handheld device, move the toggle switch to choose

the color associated with the dog collar device.

On the handheld device, set the intensity level to a numbered

position.

On the dog collar device, hold the power key for about 5

seconds until the status LED turns yellow.

While the dog collar device status LED is yellow, select a

training key on the handheld device.

The dog collar device beeps when the devices have paired

successfully.

TIP: If the devices did not pair successfully, you should verify

the batteries in both devices are fully charged and the intensity

level is set to a numbered position.

Selecting a Dog Collar Device

Before you can select and control a dog collar device, you must

pair the dog collar device with the handheld device (Pairing a

Dog Collar Device with the Handheld Device, page 2).

Move the dog collar device toggle switch to select the color

associated with a dog collar device.

The training keys control the dog collar device associated with

the selected color.

Fitting the Collar on Your Dog

CAUTION

To prevent irritation from the contact points, remove the collar

for at least eight hours out of every 24-hour period.

This device is not intended for human use. Do not attempt to

use on any person.

Do not spray the device or collar with harsh chemicals including

but not limited to flea or tick spray. Always ensure that any flea

or tick spray that is applied to the dog is completely dry before

placing the collar on the dog. Small amounts of harsh chemicals

can damage the plastic components and collar laminate.

In order to effectively train the dog, the collar and device must fit

the dog properly. If the collar is too loose or positioned

incorrectly, stimulation may be inconsistent. This can delay or

prevent successful training.

Position the device at the front of the dog's neck, with the

status LED facing toward the dog's chin and the contact

points against the throat.

TIP: For bark correction, the device contact points should be

positioned near the dog's vocal cords. This location varies

based on the breed of dog. If the device does not seem to

detect the dog's barks, you should move the device closer to

or farther from the dog's body to find the ideal location.

Tighten the strap so that it is very snug around the dog's

neck, and fasten the buckle.

NOTE: The collar should fit tightly and should not be able to

rotate or slide on the dog's neck. The dog must be able to

swallow food and water normally. You should observe your

dog's behavior to verify that the collar is not too tight.

Wiggle the device to work the contact points through the

dog's coat.

NOTE: The contact points must have contact with the dog's

skin to be effective.

If the strap is too long, cut off the excess, leaving at least

8 cm (3 in.) to spare.

TIP: You can mark the hole used to fasten the buckle for

future reference.

Selecting and Installing the Contact Points

For best results, select the correct contact points based on your

dog's coat.

2 Getting Started

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin Sport Pro Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info