Bedienungsanleitung Garmin Vector 2 (Seite 5 von 16) (Englisch)

589621

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Introduction

WARNING

Read all instructions carefully before installing and using the

Vector system. Improper use could result in serious injury.

See the Important Safety and Product Information guide in the

product box for product warnings and other important

information.

NOTICE

Go to www.garmin.com/vectorowner for the latest information

including bike compatibility, software updates, and video

tutorials.

Thank You

Thank you for your Vector or Vector S purchase. This manual

covers both Vector systems.

Vector was designed for cyclists, by cyclists, to provide an

outstanding experience of owning a precision power

measurement system for your bike.

Vector is simple, accurate, and easy to use.

For software updates, video tutorials, and everything you need

to get years of service out of your Vector, go to

www.garmin.com/vectorowner.

Now it's time to put the power under your feet and get out there

and ride.

Getting Started

Install the Vector components (Installing the Vector

Components).

Install the shoe cleats (Installing the Shoe Cleats).

Pair Vector with your Edge

device (Paring Vector with Your

Edge 1000).

Go for a ride (Your First Ride).

View your history (Vector Data).

Send your history to your computer (Sending Your Ride to

Garmin Connect).

Tools Included

• 15 mm crowfoot adapter for torque wrench

• 2.5 mm hex key

Tools Needed

• 15 mm pedal wrench

• Bike grease

• 3 mm hex key

• 4 mm hex key

Installing the Vector Components

The installation steps for the Vector and Vector S systems are

very similar. Procedures that are specific to the Vector S system

are noted.

Preparing for the Installation

Confirm the compatibility of your bike at www.garmin.com

/vectorowner.

Find the sensor ID that is engraved on the spindle, and write

it down.

Remove the existing pedals.

Clean the threads, and remove old grease.

Determining the Bicycle Chain Clearance

Before you can install the right pedal, you must determine

bicycle chain clearance.

Move your bike chain to the largest chain ring and the

smallest cassette gear.

The bike chain should be in the outermost position to

determine proper clearance between the pedal pod cable and

the chain.

NOTE: There must be at least 5 mm clearance

between

the chain and the crank arm.

Installing the Pedal and Pedal Pod

This procedure is for the Vector system. For the Vector S

system, see Installing the Left Pedal and Pedal Pod.

NOTE: The left and right pedal pods are the same.

Install the left pedal first.

Apply a thin layer of grease on the pedal spindle threads

Insert the spindle into the crank arm

Hand tighten the spindle.

NOTE: The left pedal spindle has a left-handed (reverse)

thread.

Use the pedal wrench to tighten the spindle.

NOTE: Garmin

recommends torque of 25 to 30 lbf-ft. (34 to

40 N-m).

Clean all excess grease from the spindle using a clean cloth

and soapy water or isopropyl alcohol.

Place the pedal pod

on the spindle.

NOTE: You must carefully bend the cable

out of the way.

The pedal pod should be flat against the crank arm.

TIP: Power and cadence calculations are not impacted by the

orientation of the pedal pod. Garmin recommends placing the

pedal pod on the leading edge of the crank. When the crank

is in the forward position, the pedal pod should be pointing

downward.

Firmly plug the cable into the spindle.

Insert the screw

into the pedal pod, and use the 2.5 mm

hex key to tighten the screw.

Rotate the crank arm to check for clearance.

The pedal pod should not interfere with any part of the bike.

Repeat steps 2 through 10 to install the right pedal and pedal

pod.

NOTE: If the pedal pod cable rubs the chain, you can add

one or two washers between the spindle and the crank arm

to increase clearance. Do not use more than two washers.

Introduction 1

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin Vector 2 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info