Bedienungsanleitung Garmin Venu 2S (Seite 53 von 68) (Englisch)

772762

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Pairing Your Wireless Sensors

The first time you connect a wireless ANT+ or Bluetooth sensor to your Garmin device, you must pair the device

and sensor. After they are paired, the device connects to the sensor automatically when you start an activity and

the sensor is active and within range.

TIP: Some ANT+ sensors pair with your device automatically when you start an activity with the sensor turned

on and near the device.

1Move at least 10 m (33 ft.) away from other wireless sensors.

2If you are pairing a heart rate monitor, put on the heart rate monitor.

The heart rate monitor does not send or receive data until you put it on.

3Hold .

4Select > Sensors > Add New.

5Bring the device within 3 m (10 ft.) of the sensor, and wait while the device pairs with the sensor.

After the device connects to the sensor, an icon appears at the top of the screen.

Foot Pod

Your device is compatible with the foot pod. You can use the foot pod to record pace and distance instead of

using GPS when you are training indoors or when your GPS signal is weak. The foot pod is on standby and ready

to send data (like the heart rate monitor).

After 30 minutes of inactivity, the foot pod powers off to conserve the battery. When the battery is low, a

message appears on your device. Approximately five hours of battery life remain.

Calibrating Your Foot Pod

Before you can calibrate your foot pod, you must pair your device with the foot pod (Pairing Your Wireless

Sensors, page 47).

Manual calibration is recommended if you know your calibration factor. If you have calibrated a foot pod with

another Garmin product, you may know your calibration factor.

1Hold .

2Select > Sensors > Foot Pod > Cal. Factor.

3Adjust the calibration factor:

• Increase the calibration factor if your distance is too low.

• Decrease the calibration factor if your distance is too high.

Improving Foot Pod Calibration

Before you can calibrate your device, you must acquire GPS signals and pair your device with the foot pod

(Pairing Your Wireless Sensors, page 47).

The foot pod is self-calibrating, but you can improve the accuracy of the speed and distance data with a few

outdoor runs using GPS.

1Stand outside for 5 minutes with a clear view of the sky.

2Start a running activity.

3Run on a track without stopping for 10 minutes.

4Stop your activity, and save it.

Based on the recorded data, the foot pod calibration value changes, if necessary. You should not need to

calibrate the foot pod again unless your running style changes.

Using an Optional Bike Speed or Cadence Sensor

You can use a compatible bike speed or cadence sensor to send data to your device.

• Pair the sensor with your device (Pairing Your Wireless Sensors, page 47).

• Set your wheel size (Calibrating Your Speed Sensor, page 48).

• Go for a ride (Going for a Ride, page 26).

Wireless Sensors 47

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin Venu 2S Seite 53

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin Venu 2S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info