Bedienungsanleitung Garmin VIRB ELITE (Seite 6 von 16) (Englisch)

544111

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Keys

Select to scroll through menus and settings.

OK Select to choose menu options or to take a photo.

MODE Select to scroll through modes.

Hold to turn the device on and off.

REC Slide toward the lens to record video.

Mounting the Device

NOTICE

To prevent product loss or damage, do not use the adhesive

mounting base when the temperature is below 5°F (-15°C).

The permanent mounting adhesive is extremely difficult to

remove after it is installed.

Before you can install the adhesive mounting base onto a

surface, the ambient temperature must be from 70° to 100°F

(from 21° to 38°C).

Your device includes an assortment of mounting bases and

arms, which can be used in many configurations. These

instructions provide an example of one possible configuration.

You can also purchase additional mounts for your device, such

as wearable mounts, vehicle mounts, or a tripod mount. Go to

www.garmin.com/outdoor for more information.

NOTE: By default, the camera should be mounted with the

screen facing up to record correctly oriented video. You can

adjust the settings to record with the screen facing down

(Advanced Recording Settings).

Thoroughly clean the mounting surface using water or

alcohol.

The mounting surface must be free of dirt, debris, wax, or

coatings.

Remove the film from the adhesive mounting base

, and

press the base firmly onto the mounting surface.

You can use either the flat base or the curved base,

depending on the contour of the mounting surface.

Allow the base to bond to the mounting surface for at least

24 hours.

Place the coupler

into the base.

Place the threaded ring

over the coupler, and tighten it

onto the base.

Snap the mounting arm

into the coupler.

Insert a thumbscrew

into the larger opening of the joint,

and tighten the thumbscrew to lock the angle of the joint.

Snap the camera mount

into the top of the mounting arm.

Insert a thumbscrew into the larger opening of the joint, and

tighten the thumbscrew to lock the angle of the joint.

Place the tab

on the back of the camera mount into the

slot in the back of the camera.

Squeeze the buttons

on the sides of the mount, press the

front of the camera

down, and release the buttons.

The camera should be held tightly and should not move in

the mount when properly secured.

If the camera feels loose in the mount, press the front of the

camera into the mount until it clicks.

Turning On the Device

Select .

Turning Off the Device

NOTICE

To prevent loss of data, always turn off the device before

removing the battery.

NOTE: You cannot turn off the device while recording video.

If necessary, slide REC away from the lens.

Hold .

appears on the screen while the device saves track log data

and turns off.

2 Introduction

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin VIRB ELITE Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin VIRB ELITE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info