Bedienungsanleitung Garmin VIRB Ultra 30 Actioncam (Seite 8 von 22) (Englisch)

657479

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

Attaching the Device to the Mount

NOTICE

To prevent product loss or damage, do not use the adhesive

mounting base when the temperature is below -15°C (5°F).

The permanent mounting adhesive is extremely difficult to

remove after it is installed.

Before you can install the adhesive mounting base onto a

surface, the ambient temperature must be from 21° to 38°C

(from 70° to 100°F).

Your device includes an assortment of mounting bases and

arms, which can be used in many configurations. These

instructions provide an example of one possible configuration.

You can also purchase additional mounts for your device, such

as wearable mounts, vehicle mounts, or a tripod mount. Go to

www.garmin.com/VIRB for more information.

Thoroughly clean and dry the mounting surface using water

or alcohol.

The mounting surface must be free of dirt, debris, wax, or

coatings.

Remove the film from the adhesive mounting base

, and

press the base firmly onto the mounting surface.

You can use either the flat base or the curved base,

depending on the contour of the mounting surface.

Allow the base to bond to the mounting surface for at least 24

hours.

TIP: For the best results, you can place a large book or other

heavy object on the mounting base during the 24-hour

bonding period. This applies pressure to the adhesive and

can help improve the strength of the bond.

Insert the adapter

into the base.

The lever

must be in the open position.

Snap the lever to the closed position to lock the adapter into

the base.

The lever must be flush with the base.

Insert the camera mount

into the top of the adapter.

The device should be horizontal for the proper aspect ratio

when recording video.

Insert a thumbscrew

into the larger opening of the joint,

and tighten the thumbscrew to lock the angle of the joint.

NOTE: The metal fitting indicates the smaller opening of the

joint.

If necessary, insert the included hex wrench into the end of

the thumbscrew to adjust the tightness of the joint.

Voice Control

The voice control feature allows you to control your camera by

saying words and commands in English.

NOTE: The voice control feature is available only in English.

You can use this feature while the interface is set to a different

language, but you must speak the commands in English.

Turning Voice Control On or Off

From the main menu, select > Voice Control.

Controlling the Camera Using Voice

Commands

Say OK, Garmin to activate the voice control feature.

The camera plays a tone and starts listening for a command.

Say a command:

• To take a photo, say Take a Photo or Take a Picture.

• To start recording video, say Start Recording.

• To stop recording video, say Stop Recording.

NOTE: You can stop recording using a voice command

only if you started recording using a voice command.

• To place a bookmark in the video while you are recording,

say Remember That.

This option allows you to mark key moments in the video

as they occur so that you can find them easily while

editing the video.

The camera plays a tone when it recognizes your command.

Voice Control Tips

• Speak in a normal voice directed at the device.

• Reduce background noise to increase the accuracy of the

voice recognition.

• Before each command, say OK, Garmin.

• Listen for a tone to confirm that the camera successfully

recognized a command.

• Watch the status LEDs to confirm the camera recognized the

command.

The LEDs flash green twice to indicate the camera

recognized the command. The LEDs flash red twice to

indicate the command was not recognized.

Video

Recording a Video

NOTE: If the battery power becomes very low while recording

video, the device automatically stops recording, saves the video,

and safely turns off. The status LEDs flash rapidly when the

battery charge level is low.

Move the recording switch forward to start recording video.

NOTE: For the best audio quality, do not touch or cover the

microphone area, except with an approved case.

If the device is off, it turns on automatically. The device starts

recording video immediately, and the red light turns on.

Move the recording switch backward to stop recording video.

The video is saved on the memory card as an .mp4 file. The

G-Metrix sensor data is saved on the memory card as a .fit

file.

Video Settings

From the main menu, select Video.

NOTE: Not all settings are available for all video modes.

4 Voice Control

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin VIRB Ultra 30 Actioncam Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin VIRB Ultra 30 Actioncam

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info