Bedienungsanleitung Garmin VOLVO PENTA GLASS COCKPIT GPSMAP 7400 (Seite 65 von 76) (Englisch)

691432

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Setting the Water Temperature Offset

Before you can set the water temperature offset, you must have

a NMEA 0183 water-temperature sensor or a temperature-

capable transducer to measure water temperature.

The temperature offset compensates for the temperature

reading from a temperature sensor.

Measure the water temperature using the temperature sensor

or temperature-capable transducer that is connected to the

chartplotter.

Measure the water temperature using a different temperature

sensor or a thermometer that is known to be accurate.

Subtract the water temperature measured in step 1 from the

water temperature measured in step 2.

This is the temperature offset. Enter this value in step 5 as a

positive number if the sensor connected to the chartplotter

measures the water temperature as being colder than it

actually is. Enter this value in step 5 as a negative number if

the sensor connected to the chartplotter measures the water

temperature as being warmer than it actually is.

Select Settings > My Vessel > Temp. Offset.

Enter the temperature offset calculated in step 3.

Calibrating a Water Speed Device

If you have a speed-sensing transducer connected to the

chartplotter, you can calibrate that speed-sensing device to

improve the accuracy of water-speed data displayed by the

chartplotter.

Select Settings > My Vessel > Calibrate Water Speed.

Follow the on-screen instructions.

If the boat is not moving fast enough or the speed sensor is

not registering a speed, a message appears.

Select OK, and safely increase the boat speed.

If the message appears again, stop the boat, and ensure the

speed-sensor wheel is not stuck.

If the wheel turns freely, check the cable connections.

If you continue to get the message, contact Garmin product

support.

Adding a Key

You can add keys to the system. The system can have up to

four keys, which are numbered from 1 to 4.

Select Settings > My Vessel > e-KEY Management > Add

e-KEY.

When prompted, hold the new key in front of the panel.

The system will store the key ID.

Setting the Speed Factor

Before you can set the speed factor, you must compare the

displayed vessel speed with an external data source for speed,

such as GPS or another vessel.

Before you can set the speed factor, the vessel must be under

way.

Select Settings > My Vessel > Speed Factor.

Enter the difference between the displayed speed and the

external data.

Verify that the two speed sources are displaying the same

value.

Fuel Tank Settings

Select Settings > My Vessel > Fuel Tank, and select a

driveline.

For more information, refer to the Volvo Penta manual.

Volume: Sets the fuel capacity of this fuel tank on your vessel.

Empty Tank: Calibrates the empty tank level.

Multipoint: Calibrates various fuel levels between empty and

full.

Full Tank Calibration: Calibrates the full tank level.

Seven Marine Engine Installation Settings

Select Settings > My Vessel > Seven Marine Installation.

DPS Button: Allows you to set the joystick button DPS modes.

Trim Zero Set: Allows you to initialize the trim angle to zero

when all motors are fully trimmed down.

Tank Preset: Sets the tank name, fluid type, sensor style, and

tank capacity, and calibrates the sensor (Configuring the

Tank Level Sensors, page 43).

Air Purge: Allows you to bleed air from the steering system

using the steering pumps.

Steer Sensor: Calibrates the engine steering system using

physical end stops. A physical end stop is the point at which

a steering wheel stops turning in a direction.

Joystick Thrust: Allows you to set how hard the thrusters work.

Larger boats may need to select Maximum for the boat to

move, while Maximum joystick thrust may provide too much

thrust for smaller boats.

Lock to Lock: Allows you to set the number of turns from lock to

lock.

Steer Friction: Sets the friction on the steering wheel. The

friction is adjusted automatically according to the engine

speed.

Engine Distance: Allows you to set the distance between drive

lines to limit achievable steering angles for certain engine

distances.

Gear Rotation: Allows you to set the type of gear case on the

outboard to define forward and reverse shift direction.

Gear Ratio: Allows you to set the ratio between the rotation

rates of the last and first gears.

Other Vessels Settings

When your compatible chartplotter is connected to an AIS

device or VHF radio, you can set up how other vessels are

displayed on the chartplotter.

Select Settings > Other Vessels.

AIS: Enables and disables AIS signal reception.

DSC: Enables and disables digital selective calling (DSC).

Collision Alarm: Sets the collision alarm (Setting the Safe-Zone

Collision Alarm, page 10).

AIS-EPIRB Test: Enables test signals from Emergency Position

Indicating Radio Beacons (EPRIB).

AIS-MOB Test: Enables test signals from man overboard (MOB)

devices.

AIS-SART Test: Enables test transmissions from Search and

Rescue Transponders (SART).

Settings that are Synced on the Garmin

Marine Network

The following devices sync certain settings when connected to

the Garmin Marine Network.

• ECHOMAP

™

70 series

• GPSMAP

507 series (software version 3.0 or later)

• GPSMAP 701 series (software version 3.0 or later)

• GPSMAP 702 series

• GPSMAP 800 series

• GPSMAP 902 series

• GPSMAP 1000 series

• GPSMAP 1002 series

Device Configuration 57

Garmin VOLVO PENTA GLASS COCKPIT GPSMAP 7400 Seite 65

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin VOLVO PENTA GLASS COCKPIT GPSMAP 7400

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info