Bedienungsanleitung Garmin VOLVO PENTA GLASS COCKPIT GPSMAP 7600 (Seite 64 von 76) (Englisch)

691433

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

GPS Accuracy: Sets an alarm to sound when the GPS location

accuracy falls outside the user-defined value.

Sonar Alarms

NOTE: Not all options are available on all transducers.

From an applicable sonar view, select Menu > Sonar Setup >

Alarms.

You can also open the sonar alarms by selecting Settings >

Alarms > Sonar.

Shallow Water: Sets an alarm to sound when the depth is less

than the specified value.

Deep Water: Sets an alarm to sound when the depth is greater

than the specified value.

FrontVü Alarm: Sets an alarm to sound when the depth in front

of the vessel is less than the specified value, which can help

you avoid running aground (Setting the FrontVü Depth Alarm,

page 31). This alarm is available only with Panoptix FrontVü

transducers.

Water Temp.: Sets an alarm to sound when the transducer

reports a temperature that is 2°F (1.1°C) above or below the

specified temperature.

Contour: Sets an alarm to sound when the transducer detects a

suspended target within the specified depth from the surface

of the water and from the bottom.

Fish

Fish: Sets an alarm to sound when the device detects a

suspended target.

• sets the alarm to sound when fish of all sizes are

detected.

• sets the alarm to sound only when medium or large

fish are detected.

• sets the alarm to sound only when large fish are

detected.

Setting Weather Alarms

Before you can set weather alarms, you must have a compatible

chartplotter connected to a weather device, such as a GXM

device, and have a valid weather subscription.

Select Settings > Alarms > Weather.

Turn on alarms for specific weather events.

Setting the Fuel Alarm

You can set an alarm to sound when the total amount of

remaining onboard fuel reaches the level you specify.

Select Settings > Alarms > Fuel.

If necessary, select a driveline.

Select On.

Enter the remaining amount of fuel that triggers the alarm.

If necessary, repeat steps 2–4 for all drivelines.

My Vessel Settings

NOTE: Some settings and options require additional charts or

hardware.

Select Settings > My Vessel.

For more information, refer to the Volvo Penta manual.

Depth and Anchoring: Allows you to enter information about

the keel (Setting the Keel Offset, page 22) and the anchor.

The Anchor Height value is the height of the anchor above

the waterline. The Anchor Scope value is the ratio of the

length of anchor rode in use to the vertical distance from the

bow of the vessel to the bottom of the water. These anchor

settings are used to calculate the Target Anchor Rode date

field.

Temp. Offset: Allows you to set an offset value to compensate

for the water temperature reading from a NMEA 0183 water-

temperature sensor or a temperature-capable transducer

(Setting the Water Temperature Offset, page 57).

Calibrate Water Speed: Calibrates the speed-sensing

transducer or sensor (Calibrating a Water Speed Device,

page 57).

Vessel Type: Enables some chartplotter features based on the

boat type.

CZone™: Sets the digital switching circuits.

SeaStar Instance: Sets the digital switching circuits.

e-KEY Management: Allows you to manage the electronic keys

(e-KEYs).

Drive Type: The setting should be changed by authorized Volvo

Penta personnel only.

ACP Mode: Sets the ACP protection mode.

Toe Angle: The setting should be changed by authorized Volvo

Penta personnel only.

Speed Factor: Calibrates the displayed boat speed.

PTA Settings: Allows you to enter new maximum limits for the

PTA modes.

Fuel Tank: Sets the fuel tank settings.

Seven Marine Installation: Sets the Seven Marine engine

settings.

Hull ID Number: Allows you to enter the Hull Identification

Number (HIN).The HIN might be permanently affixed to the

upper starboard side of the transom or outboard side.

Setting the Keel Offset

You can enter a keel offset to compensate the water depth

reading for the transducer installation location. This allows you

to view the depth of the water below the keel or the true depth of

the water, depending on your needs.

If you want to know the water depth below the keel or the lowest

point of your boat and the transducer is installed at the water

line or anywhere above the end of the keel, measure the

distance from the transducer location to the keel of the boat.

If you want to know the true water depth and the transducer is

installed below the water line, measure the distance from the

bottom of the transducer up to the water line.

NOTE: This option is only available when you have valid depth

data.

Measure the distance:

• If the transducer is installed at the water line or

anywhere above the end of the keel, measure the

distance from the transducer location to the keel of the

boat. Enter this value as a positive number.

• If the transducer is installed at the bottom of the keel

and you want to know the true depth of the water,

measure the distance from the transducer to the water

line. Enter this value in as a negative number.

Select Settings > My Vessel > Depth and Anchoring >

Keel Offset.

Select if the transducer is installed at the water line, or

select if the transducer is installed at the bottom of the

keel.

Enter the distance measured in step 1.

56 Device Configuration

Garmin VOLVO PENTA GLASS COCKPIT GPSMAP 7600 Seite 64

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin VOLVO PENTA GLASS COCKPIT GPSMAP 7600

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info