Bedienungsanleitung Garmin VOLVO PENTA GLASS COCKPIT GPSMap 8000 (Seite 19 von 66) (Englisch)

691431

Zoom out

Zoom in

Vorherige Seite

1/66

Nächste Seite

Loop: Shows a loop of forecasted or observed weather

information.

Legend: Shows the weather legend, with the severity of the

conditions increasing from left to right.

Weather Subscription: Shows weather subscription

information.

Restore Defaults: Resets the weather settings to factory default

values.

Edit Overlays: Adjusts the data shown on the screen

(Customizing the Data Overlays, page 3).

Radar Overlay Settings

From the Navigation or Fishing chart, select Menu > Layers >

Radar > .

From a radar screen, select Menu.

Radar To Standby: Stops radar transmission.

Gain: Adjusts the gain (Adjusting Gain on the Radar Screen

Automatically, page 30).

Sea Clutter: Adjusts the sea clutter (Adjusting Gain on the

Radar Screen Automatically, page 30).

Radar Options: Opens the radar options menu (Radar Options

Menu, page 31).

Other Vessels: Sets how other vessels are displayed on the

radar view (Other Vessels Layer Settings, page 10).

Radar Setup: Opens the radar display settings (Radar Setup

Menu, page 32).

Edit Overlays: Adjusts the data shown on the screen

(Customizing the Data Overlays, page 3).

Chart Settings

NOTE: Not all settings apply to all charts and 3D chart views.

Some settings require external accessories or applicable

premium charts.

From a chart, select Menu > Settings.

Orientation: Sets the perspective of the map.

Detail: Adjusts the amount of detail shown on the map, at

different zoom levels.

World Map: Uses either a basic world map or a shaded relief

map on the chart. These differences are visible only when

zoomed out too far to see the detailed charts.

Start Line: Sets the starting line for the sailing race.

Inset Map: Shows a small map centered on your present

location.

Fish Eye 3D Settings

NOTE: This feature is available with premium charts, in some

areas.

From the Fish Eye 3D chart view, select Menu.

View: Sets the perspective of the 3D chart view.

Tracks: Shows tracks.

Sonar Cone: Shows a cone that indicates the area covered by

the transducer.

Fish Symbols: Shows suspended targets.

Supported Maps

To help you have a safe and enjoyable time on the water,

Garmin devices only support official maps produced by Garmin

or an approved third party producer.

You can purchase maps from Garmin. If you purchase maps

from a seller other than Garmin, investigate the seller before

purchasing. Be extra cautious with online sellers. If you have

purchased an unsupported map, return it to the seller.

Garmin Quickdraw Contours Mapping

WARNING

The Garmin Quickdraw Contours mapping feature allows users

to generate maps. Garmin makes no representations about the

accuracy, reliability, completeness or timeliness of the maps

generated by third parties. Any use or reliance on the maps

generated by third parties is at your own risk.

The Garmin Quickdraw Contours mapping feature allows you to

instantly create maps with contours and depth labels for any

body of water.

When Garmin Quickdraw Contours records data, a colored

circle surrounds the vessel icon. This circle represents the

approximate area of the map that is scanned by each pass.

A green circle indicates good depth and GPS position, and a

speed under 16 km/h (10 mph). A yellow circle indicates good

depth and GPS position, and a speed between 16 and 32 km/h

(10 and 20 mph). A red circle indicates poor depth or GPS

position, and a speed above 32 km/h (20 mph).

You can view Garmin Quickdraw Contours in a combination

screen or as a single view on the map.

The amount of saved data depends on the size of your memory

card, your sonar source, and the speed of your boat as you

record data. You can record longer when you use a single-beam

sonar. It is estimated that you might be able to record about

1,500 hours of data onto a 2 GB memory card.

When you record data on a memory card in your chartplotter,

the new data is added to your existing Garmin Quickdraw

Contours map, and is saved on the memory card. When you

insert a new memory card, the existing data does not transfer

onto the new card.

Mapping a Body of Water Using the Garmin

Quickdraw Contours Feature

Before you can use the Garmin Quickdraw Contours feature,

you must have sonar depth, your GPS position, and a memory

card with free space.

From a chart view, select Menu > Quickdraw Contours >

Start Recording.

When recording is complete, select Menu > Quickdraw

Contours > Stop Recording.

Select Manage > Name, and enter a name for the map.

Adding a Label to a Garmin Quickdraw

Contours Map

You can add labels to a Garmin Quickdraw Contours map to

mark hazards or points of interest.

From the Navigation chart, select a location.

Select Add Quickdraw Label.

Enter text for the label, and select Done.

Garmin Quickdraw Community

The Garmin Quickdraw Community is a free, public, online

community that enables you to share your Garmin Quickdraw

Contours maps with others. You can also download maps other

users have created.

Garmin Quickdraw Contours Mapping 11

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin VOLVO PENTA GLASS COCKPIT GPSMap 8000 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin VOLVO PENTA GLASS COCKPIT GPSMap 8000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info