Bedienungsanleitung Garmin Xero A1 (Seite 6 von 14) (Englisch)

691376

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

Align the arrow on the mount with the center arrow on the

curved rail.

Using a 7/64 inch hex wrench, tighten the screw at the front

of the rail mount

to a maximum torque specification of 2.2

N-m (20 lbf-in).

Align the large holes on the mount

with the mounting holes

on the side of your bow.

TIP: The mount contains three sets of mounting holes. Mount

the sight in a location that functions best with your peep sight

aperture. Mounting the sight closer to the bow may allow a

better fit in some bow cases.

Using a 1/8 inch hex wrench, secure the mount using the

included mounting screws

Tighten the mounting screws to a maximum torque

specification of 6.7 N-m (60 lbf-in).

NOTE: Do not exceed the bow manufacturer's recommended

torque values.

Securing the Trigger

Position the ranging trigger

on the grip of your bow where

you can comfortably activate it at full draw.

NOTE: You should confirm the trigger and the trigger cable

are positioned so they do not interfere with the operation of

the bow.

Secure the trigger to the bow using the included tape

TIP: You can use the extra piece of tape to secure the trigger

cable to the riser.

Turning the Device On or Off

To turn on the device, press .

To turn off the device, hold for 3 sec.

Calibrating the Bow Sight

The first time you turn on the Xero bow sight, you are prompted

to go through initial setup steps. You can view tutorial videos at

www.garmin.com/xerotutorials.

Select a language.

Select a unit of measure.

Select Yes to start the pin calibration procedure.

Select a ranged pin color (A1i model only).

If necessary, select Yes to adjust the pin and rangefinder

reticle brightness and follow the on-screen instructions.

Set the primary pin (Setting the Primary Pin, page 2).

Select Done.

Align the rangefinder with the primary pin (Aligning the

Rangefinder with the Primary Pin, page 3).

Select Done.

Follow the on-screen instructions to complete the pin

calibration procedure and set pins for additional distances.

Torque Specifications

When adjusting and tightening the mounting screws, you should

ensure the screws are always tightened to a maximum torque

specification of 2.2 N-m (20 lbf-in.). If you do not have a torque

wrench, you can tighten the screws until the screw head makes

contact with the mount surface, then tighten the screw an

additional one quarter turn.

Setting the Primary Pin

The primary pin is a fixed point on the device optic that points

along the same axis as the laser rangefinder. You can change

the primary pin's alignment by adjusting the straight vertical and

horizontal adjustments on the mount. After you set the primary

pin, you can set additional pins for different distances using the

device software.

Aim at a target that is a minimum distance of 15 m (15 yd.)

away.

NOTE: If you set your primary pin for farther distances, such

as 30 m (33 yd.), you will have a farther maximum range, but

2 Calibrating the Bow Sight

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin Xero A1 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin Xero A1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info