Bedienungsanleitung Garmin XS Series speakers (Seite 6 von 10) (Englisch)

801437

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

Connecting the LED Wires to Power

NOTE: This feature is available on only the sports model.

You must connect all 12 Vdc wiring to the LEDs to a 3 A fuse at the power-source end of the cable. You should

connect the positive (+) power wire to a 12 Vdc power source through an isolator switch or circuit breaker to

turn the LEDs on and off. You can use the same isolator or circuit breaker controlling the power supply to your

stereo, which allows you to turn the LEDs and the stereo on and off at the same time.

You should use 20 AWG (0.5 through .75 mm2) or thicker wire to connect the LEDs to the battery.

1Route the positive power (+) and negative ground (-) wires from the LED-wire connections to the battery.

2Connect the negative wire to the negative (-) battery terminal.

3Connect the positive wire to the positive (+) terminal through a 3 A fuse and isolator switch or circuit breaker.

Speaker Information

True-Marine™ Products

True-Marine products are subjected to rigorous environmental testing under harsh marine conditions to surpass

industry guidelines for marine products.

Any product that bears the True-Marine stamp of assurance has been designed for simplicity of use and

combines advanced marine technologies to deliver an industry leading entertainment experience. All True-

Marine products are supported by the Fusion 3-year worldwide limited consumer warranty.

Registering Your Fusion Device

Help us better support you by completing our online registration today.

• Go to www.fusionentertainment.com.

• Keep the original sales receipt, or a photocopy, in a safe place.

Cleaning the Speakers

NOTE: When mounted correctly, these speakers are rated IP65 for dust and water ingress protection under

normal conditions. They are not designed to withstand high pressure water spray, which may occur when you

wash down your vessel. Failure to carefully spray-clean the vessel may damage the product and void the

warranty.

NOTICE

Do not use harsh or solvent-based cleaners on the speakers. Using such cleaners may damage the product and

void the warranty.

1Clean all salt water and salt residue from the speaker with a damp cloth soaked in fresh water.

2Use a mild detergent to remove a heavy buildup of salt or stains.

Troubleshooting

Before you contact your Fusion dealer or service center, you should perform a few simple troubleshooting steps

to help diagnose the problem.

If the Fusion speaker has been installed by a professional installation company, you should contact the

company so the technicians can assess the problem and advise you about possible solutions.

There is no sound coming from the speakers

• Verify that all connections from the source device and/or the amplifier are connected correctly to the speaker

terminals.

The system lacks bass or high frequencies

• Verify that the correct wire polarity is observed between the source and speakers.

The wires should be connected positive to positive and negative to negative.

• Verify that the speakers are attached firmly to the mounting surface.

6 XS Series Installation Instructions

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin XS Series speakers Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin XS Series speakers

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info