Bedienungsanleitung Garret Ace 200 (Seite 9 von 11) (Englisch)

647655

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

Garrett Metal Detectors ACE 200

™

SYMPTOM SOLUTION

No power

1. Ensure batteries are installed in the correct orientation.

2. Replace all old batteries with all new batteries.

Erratic sounds or

target ID cursor

movement

1. Ensure your searchcoil is securely connected and the coil

cable is snugly wound around the stem.

2. If using the detector indoors, be aware that excessive

amounts of electrical interference exists, plus excessive

amounts of metal can be found in floors and walls.

3. Determine if you are close to other metal detectors or other

metal structures such as electrical power lines, wire fences,

benches, etc.

4. Reduce your sensitivity setting.

Intermittent Signals

Intermittent signals typically mean you’ve found a deeply

buried target or one that is positioned at a difficult angle for

your detector to read. Scan from different directions to help

define the signal. In the case of multiple targets, switch to

the ZERO-DISC Mode to locate all targets. In trashy areas, use

the Super Sniper™ or a 5" x 8" DD searchcoil. NOTE: Iron

targets may cause Intermittent Signals. You can identify iron

targets in the ZERO-DISC Mode.

I’m not finding

specific targets

Ensure you are using the correct mode for the type hunting

you are doing. If specifically hunting for coins, COINS mode

should be your best choice to eliminate other undesirable

targets. You may also use the ZERO-DISC mode, which

detects all metal targets to ensure desired targets are present.

Target ID Cursor

bounces

If your Target ID Cursor bounces erratically, chances are

you’ve found a trash target. However, a Target ID Cursor may

bounce if a good target (such as a coin) is not parallel to the

searchcoil (e.g. on edge). It may also bounce if there is one

or multiple “junk” targets laying next to the good target. Scan

from different directions until your Target ID Cursor becomes

more stable.

NOTE: Large, flat pieces of iron—depending on their

orientation in the ground—can read as a good target or can

cause erratic Target ID Cursor movement.

TROUBLESHOOTING GUIDE

Low Battery

Indicator

BATTERY REPLACEMENT

The Low Battery Indicator will switch on when the detector's

batteries become weak. The detector will maintain full

performance but the batteries should be replaced soon when

this indicator appears. NiMH rechargeable batteries may be

used, but may have a shorter life per charge. You can expect

20 to 40 hours of operation depending on battery type and

quality.

Replace the batteries by sliding the cover off the control

housing. Remove batteries when the ACE 200 will be stored

for longer than 30 days.

Note: 1.5V/cell Lithium batteries can also be used, but the

use of 3.7V/cell Lithium batteries will damage the detector.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garret Ace 200 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garret Ace 200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info