714630
108
Zoom out
Zoom in
Vorherige Seite
1/132
Nächste Seite
108
system to and fro until it settles down easily on the drive rotor and achieves a
stable stand on the motor base.
CAUTION: For mounting or dismounting the mixing/mincing system at the
motor base, do not grasp the glass jug. Always grasp the collar of the blade
assembly to avoid damage to the thread connecting the glass jug and blade
assembly. Additionally, the connection could get over-tightened, making it extre-
mely difficulty to remove the blade assembly after operation.
7. Grasp the blade assembly with both hands by the collar and turn it clockwise
for fixing it to the motor base (turn it a little more than a finger's breadth after
feeling the first resistance). The appliance is now ready for operation.
CAUTION: Please keep in mind that the motor will start operation immediate-
ly, when connecting the appliance to the power supply, with the power switch and
selection dial in operating position. Thus, always switch the power switch to “O”
and selection dial to “OFF”, before plugging in the power plug.
8. Ensure that the selection dial and power switch are turned to the “OFF” position.
Then insert the power plug into an appropriate wall power outlet (see: ‘Important
Safeguards for Electrical Appliances’).
CAUTION: Do not remove the lid of the glass jug during operation! Other-
wise, due to the high power of the motor, liquids and food will be hurled out vio-
lently, and liquids will run down at the exterior of the glass jug. With hard ingre-
dients in the glass jug, always keep a hand on the lid.
Note
If the rotating speed slows down visibly during operation or the motor stalls, there
may be too much food in the glass jug, and/or there are too many too hard ingre-
dients blocking the knives (see: ‘Electronic Overload Protection’). Switch off the
appliance at the selection dial and power switch and unplug. Remove any obsta-
cles. If required, take out some food and process your food in smaller portions.
Tip: The appliance will process your food in seconds. It is better to intermediately
check the consistency of your food (after processing a few seconds) than to over-
process your food.
9. Switch the power switch at the rear of the motor base to the ON position (“I”).
Then, keeping one hand on the lid of the glass jug, turn the selection dial to
the desired speed level (see: ‘Tips for Best Results’). The motor starts agitating at
once. If not, in most cases, the threads of the processing system are not assem-
108

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Gastroback 40152 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info