use the crossed-blade knife and mincer plate in combination with the chopper attachments.
Only use either the crossed-blade knife with the mince plate or the chopper attachments at
once.
• For the case that the mincer head or the closing ring loosen while operating turn OFF the
appliance immediately and pull the plug. Operate according to the instructions ´Trouble
shooting` before turning the appliance ON again.
• Always turn the appliance off, wait for the motor to stop moving and then pull the plug
before disassembling the mincer.
• Never push the food into the feeding funnel with your fingers. Always use the feedstick
for this purpose! The mincer can not mince hard or stingily ingredients (for example: bones,
nuts, ginger). If you use hard ingredients like onions or carrots, you have to steam them before
adding them to the meet otherwise they can block the motor. If the motor is blocked turn OFF
the appliance immediately and operate according to the instructions ´Trouble shooting`.
• Before the mincer is used for the first time, all parts – with the exception of the motor block
– must be thoroughly cleaned in warm soapy water.
• To ensure that the mincer does not seize, never operate it under excessive pressure.
• Instantly switch off the mincer if the worm or knife get blocked by a hard object and
wait for approx. 6 seconds to be certain that the motor is no longer running. Switch ON
the mincer after it has been cleaned.
• Never use force operating the appliance to avoid damage of the units of the appliance.
• Never hold your face or other body parts over the feed funnel when the motor is running
because little pieces of food could be thrown out of the feed funnel.
• Take care handling the crossed-blade knife because it is very sharp.
• Never put foreign substance or hard objects into the feed funnel.
• Never repair the mincer yourself. If you discover or suspect a fault, send the mincer immediately
to your local service workshop for competent examination and repair.
• Store and use the appliance in a clean, frost free environment where it is protected
from dampness, moistness and immoderate and extraordinary burden (such as: downfall, beat,
overheating, moisture in the motor block) .
• The mincer is intended for use in the household only!
Assembling
Before first usage: Rinse all the units of the appliance that come into contact with food with water
and clean them with dishwashing detergent. Operate according to the instructions ´Care and
cleaning´.
WARNING: Ensure that the appliance is switched ‘OFF’ at the power outlet and the power
cord is unplugged.
1. Place the mincer on a flat, dry surface such as a bench top.
• Never clean the line cord or the appliance in the dishwasher, poor liquids over the
appliance or douse or dip it in water or other liquids. In case that water or other liquids ran
into the appliance while operating turn OFF the appliance immediately, pull the plug and dry
the appliance with a clean cloth (´Care and cleaning`).
• Do not use the appliance in moist and wet areas.
• Check the power supply cable regularly for wear and damage.
• The mincer must only be connected to a 230 V power supply.
• Always disconnect the power supply cable from the mains before assembling, dismantling
and cleaning the appliance or before exchanging mincing plates.
• Always uncoil the line cord completely before installing the appliance.
• Place the appliance close to a power point and connect it directly without using any extension
cords to avoid additional risks of injury through fire or voltage.
• Only install the appliance in proper form secure grounding receptacle with adequate
electric power supply (alternating current; 230/240 V, 50 Hz) and ground fault circuit interrupter.
The maximum power consumption of the appliance is 800 Watt. You should also install a fuse
with a release current of maximum 30mA. If necessary ask your electrician for help.
• Never pull, rip, bend, clamp, squish or knot the line cord. Pay attention to the line cord not
hanging of the table. Attend to nobody getting caught in loops of the line cord or pulling the
appliance of the work space. When pulling the plug always catch hold of the enclosure of
the plug.
• Carry the appliance with both hands by the motor block – never by the filling pan or the
mincer.
• The mincer must only be used to process meat and vegetables. Do not mince hard parts
such as bones. Do not mince hard-fibre foods such as ginger, etc. Do not let the motor run
longer then necessary to prevent overheating. After turning OFF the appliance the motor
needs about 6 sec. to stop moving.
• Clean the appliance straight after use and rinse off leftover food. Remove such dirt immediately
and operate according to the instructions ´Care and cleaning` before storing the appliance. Do not
let food desiccate on the appliance.
• Never clean or operate the appliance or units of the appliance with abrasive or hard
sharp-edged items. Never put the appliance or parts of the appliance in the
dishwasher for cleaning! This will cause discoloration and corrosion.
• Do not use the appliance if it is damaged or units of the appliance are damaged. Do not
use the appliance if it does not function properly or if it was excessively loaded. The appliance
is likely damaged if the appliance or units of the appliance show cracks, exorbitant wearing
down, alterations or leaks. It is also likely damaged if the drive wheel of the motorblock moves
slowly. Take the appliance for technical maintenance and repair to an authorised
specialised reparation shop.
• Never use force assembling or disassembling the appliance. The single parts should be
easily put together. Only operate the mincer after it has been carefully assembled. Never
2322
41401_Manual_Neu.qxp 01.10.2008 15:40 Seite 22
