Bedienungsanleitung Gazco Clarendon - coal (Seite 15 von 28) (Englisch)

813476

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

4. GAS SUPPLY

4.1 Having run the gas supply to the appliance, PURGE THE

SUPPLY PIPE. This is essential to expel any debris that may

block the gas controls. Connect the gas supply to the

8mm-compression elbow at the right hand rear corner of

the appliance.

AR0934

There is a cutout in the right hand rear leg to enable a

direct straight connection to be made to the rear of the

appliance. See Diagram 1. A gas soundness check must be

completed up to the gas inlet connection.

4.2 Check the pull of the flue system by applying a lighted

smoke pellet to the flue system opening. If there is a

definite flow into the chimney, proceed with the

installation. If not, warm the chimney for a few minutes.

IF THERE IS STILL NO DEFINITE FLOW, THE FLUE MAY

REQUIRE ATTENTION - SEEK EXPERT ADVICE

4.3 The flue system may now be connected to the appliance.

Ensure that all joints are sealed with a suitable fire resistant

sealant. It is also recommended that a physical retention

method be used at the flue spigot joint, self-tapping screws

are recommended.

4.4 Connect a suitable pressure gauge to the test point located

on the inlet fitting and turn on the gas supply. Light the

appliance and check all gas joints for gas soundness. Turn

the appliance to a maximum and check that the supply

pressure is as stated on the databadge. Turn the gas off and

replace the test point screw. Turn the gas on and check the

test point for gas soundness.

5. CLOSURE PLATE INSTALLATION

NOTE: The Small & Medium stoves are also suitable for

installation into a fireplace opening. The following

method illustrates how this can be achieved with the aid

of the optional closure plate and spigot extension. Ensure

the fireplace dimensions are as shown in Diagram 2.

5.1 Place the closure plate against the fireplace opening and

ensure there is sufficient overlap around the perimeter to

allow a fume tight seal to be made. Cut straight across the

top of the plate if trimming is required.

5.2 Seal the plate to the opening and the hearth with a suitable

heat resisting material. Ensure that any relief opening at the

bottom of the plate is left unobstructed.

5.3 Secure the spigot extension to the engine assembly and seal

with heat resisting tape or similar. Position the engine

assembly ensuring 50mm rear clearance is maintained (see

Diagram 2) and then proceed with the installation as

detailed in points 3.2 to 3.3 above.

AR0377

6. FUEL BED ARRANGEMENT

The major ceramic components can be found inside the

firebox. Remove the cast iron door using the tool provided,

and remove all the protective packaging from these

components. See Diagram 3.

AR0540

NOTE: THE CAST IRON IS HEAVY, TAKE EXTREME CARE

WHEN HANDLING.

The loose coals should be arranged as specified in the

following steps. Care should be taken to ensure that there is

sufficient space between the coals to allow flames to pass

through.

INSTALLATION INSTRUCTIONS

INSTALLATION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gazco Clarendon - coal Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info