Bedienungsanleitung Gazco Clarendon - Conventional Flue (Seite 26 von 32) (Englisch)

813472

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

1. General

IMPORTANT: ALWAYS WEAR THE GLOVES

PROVIDED WHEN HANDLING AN IVORY

PAINTED APPLIANCE.

1.1 All main components can be replaced without removing the

appliance from its installation.

1.2 Ensure the appliance and surrounds are cool before servicing.

IT IS ESSENTIAL THAT THE GAS SUPPLY TO THE

APPLIANCE IS TURNED OFF AT THE ISOLATION

DEVICE BEFORE PROCEEDING FURTHER.

1.3 If, for any reason, the flue has to be removed from the

appliance, the seals must be replaced.

2. Removing the Door

IMPORTANT: THE OUTER PANELLING AND DOOR

OF THE APPLIANCE IS MADE FROM CAST IRON .

TAKE CARE WHEN INSTALLING, REMOVING AND

STORING TO AVOID DAMAGING THE OUTER

CASING, HEARTH OR DOOR.

2.1 Remove the 4 black nuts retaining the door, see Diagram 1.

Take care when removing the door as it is heavy. Place

carefully to one side.

2.2 Lift out the log guard and carefully remove the ceramic fuel

bed components.

2.3 Refit in reverse order.

2.4 Ensure that the rope seal on the back of the door is intact,

locate the door on the 4 studs and slide back to the firebox.

Secure in place using the 4 dome nuts and tool supplied. Do

not over tighten the nuts, see Diagram 1.

NEVER OPERATE THE APPLIANCE WHEN THE DOOR

IS REMOVED, OR THE GLASS IS BROKEN.

2.5 Replace ALL of the securing nuts ensuring that a nut is

present on all fixing studs.

UNDER NO CIRCUMSTANCES SHOULD THE

APPLIANCE BE USED IF ANY OF THE DOOR

RETAINING NUTS ARE LOOSE OR MISSING.

3. Main Burner

3.1 Turn the gas supply off at the isolation device, remove the

door and place to one side, carefully remove the ceramic

fuel bed components.

3.2 Remove the 3 securing screws, 2 at the rear and 1 at the

front left hand side, see Diagram 2.

3.3 Raise the left hand side of the burner to clear the bracket,

draw the left hand side forward.

The burner venturi is engaged over the injector. When

removing the burner be sure to clear the injector, this will

release the right hand side of the burner.

Take care when removing the burner so as not to

damage the pilot burner.

3.4 To replace the burner, engage the venturi over the injector

ensuring the burner sits on top of the fixing bracket. Push

the burner to the right and whilst holding, insert the three

fixing screws.

NOTE: BEFORE REPLACING THE BURNER, ENSURE

THE SILICONE SEAL AROUND THE INJECTOR IS

INTACT AND CHECK THAT VENTURI COVER IS

ATTACHED.

4. Pilot Unit

The pilot assembly consists of five components, which can

be individually changed, these are:

4a) Pilot burner bracket

4b) Pilot injector

4c) Electrode

4d) Thermocouple

4e) Gasket.

4.1 Turn the gas supply off at the isolation device, remove the

door and place to one side, carefully remove the ceramic

fuel bed components.

4.2 Remove the main burner, see Section 3.

Servicing Instructions - Replacing Parts

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gazco Clarendon - Conventional Flue Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info