Bedienungsanleitung Gazco Liberty 85 (Seite 10 von 76) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Norwegisch)

813338

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

INSTALLATION

GENERAL

TOOLS REQUIRED

No tools are required to install this appliance.

UNPACKING THE APPLIANCE

WARNING! DO NOT use this appliance if any part has been

exposed to water.

Immediately call a qualified service technician to inspect and to

replace any part of the electrical system if necessary.

Open the packaging carefully and remove the polystyrene.

Remove and discard the plastic bag.

Keep plastic wrapping away from children.

Be responsible when handling the packing materials.

Check all parts and accessories are removed before disposing of

any packaging.

If necessary keep the original packaging for future transport and/or

storage.

Test the appliance before installation.

This appliance is heavy and does not require

anchoring to the hearth or floor, but in certain

circumstances the appliance can become

unstable e.g. when leaning on the appliance. If

this is likely, secure the appliance to the hearth

or floor with suitably strong fixings.

FITTING THE APPLIANCE

Your new Liberty 85 may be installed virtually anywhere in your

home. However, when choosing a location ensure that the general

instructions are followed.

For best results, install out of direct sunlight.

The appliance should ideally be located close to a suitable mains

socket to enable connection. An extension could be run from an

existing socket outlet but this must be carried out by a suitably

qualified electrical engineer.

The electrical socket must be easily accessible to allow

disconnection when the appliance is fitted.

If the power cord is damaged, it must be repaired by the

manufacturer, its authorised service centre or professional person.

This appliance must stand on a clean, level, firm surface.

Do not stand the appliance on a carpet. Ensure that furniture,

curtains etc. are positioned no closer than 1m and the appliance

stands on a surface that can withstand temperatures of 90°C for

prolonged periods. Do not allow rugs to be placed within 500mm of

the front of the appliance.

Ensure that curtains and furniture are not positioned close to the

chosen position, as this would create a potential fire hazard or

block the heater outlet ducts.

WARNING! KEEP ANY COMBUSTIBLE MATERIALS AT LEAST

1M FROM THE FRONT OF THE APPLIANCE.

SERVICING AND SUPPORT

Servicing and Support

To keep your appliance looking and performing at its best, it

must be serviced annually. This service must be undertaken

by a suitably qualified individual and your retailer can organise

this for you. Alternatively, Gazco offer a manufacturers premium

service with our friendly team of qualified engineers which can

be booked at www.gazco.com/support

SERVICING REQUIREMENTS

DURING SERVICING OF THIS APPLIANCE IT MAY BE

NECESSARY TO CUT CABLE TIES IN ORDER TO

ACCESS AND REMOVE SOME OF THE PARTS.

THESE MUST BE REPLACED WHEN

REASSEMBLING THE APPLIANCE.

THIS APPLIANCE MUST ONLY BE SERVICED BY A SUITABLY

QUALIFIED PERSON.

BEFORE UNDERTAKING ANY WORK ON THE APPLIANCE:

SWITCH OFF THE APPLIANCE AND ISOLATE THE POWER

SUPPLY ENSURING THERE IS NO POWER TO THE APPLIANCE.

Wait for at least 10 minutes until the appliance has cooled down.

Remote Handset Battery Replacement

Replace with 2 AAA batteries. Make sure the batteries are installed

correctly in the remote control.

NOTE: The remote control has a Battery Status

indicator (top right corner), after an extended

period of displaying empty the LED screen will

cease to function despite the handset still being

able to send commands.

Replace the batteries to restore display.

Maintenance of Motors

The motor used on the flame effect is pre-lubricated for extended

bearing life and requires no further lubrication. However, periodic

cleaning/vacuuming of the heater unit is recommended.

Resetting the Thermal Cutout Switch

The appliance is fitted with an Electronic Safety Control (E.S.). This

is a safety device which switches off the fire if, the appliance

overheats for any reason e.g. when covered.

If the heater stops operating whilst the flame effect continues

normally, this indicates that the E.S. Control is in operation.

The E.S. Control can only be re-set after the appliance has cooled

down.

To re-set the E.S:

Switch off the appliance (Manual On/Off switch) and leave for

approximately 120 minutes.

Remove any obstruction to the fan heater outlet or other internal

parts.

Switch on appliance and the E.S. Control will re-set. Ensure that

the appliance is functioning correctly. If the E.S. Control operates

again, the appliance should be checked by a competent Electrician.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gazco Liberty 85 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info