Bedienungsanleitung Gazco Loft Conventional Flue (Seite 12 von 52) (Englisch)

813398

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

INSTALLATIONS INSTRUCTIONS

SITE REQUIREMENTS

SAFETY PRECAUTIONS

This appliance must be installed according to local and national

codes of practice. Failure to install the appliance correctly could

lead to prosecution. Read these instructions before installing

and using this appliance.

These instructions must be left intact with the user.

Do not attempt to burn rubbish on this appliance.

Keep all plastic bags away from young children.

Do not place any object on or near to the appliance and allow

adequate clearance above the appliance.

IF THE APPLIANCE IS EXTINGUISHED OR GOES OUT IN USE,

WAIT 3 MINUTES BEFORE ATTEMPTING TO RELIGHT THE

APPLIANCE.

IMPORTANT: REFER TO DATA BADGE AND

TECHNICAL SPECIFICATION AT THE FRONT OF

THE MANUAL TO ENSURE THE APPLIANCE IS

CORRECTLY ADJUSTED FOR THE GAS TYPE AND

CATEGORY APPLICABLE IN THE COUNTRY OF

USE.

FOR DETAILS OF CHANGING BETWEEN GAS TYPES

REFER TO SERVICING INSTRUCTIONS.

FLUE & CHIMNEY REQUIREMENTS

WHEN INSTALLING A FLUE SYSTEM PLEASE REFER TO THE

MANUFACTURERS INSTRUCTIONS.

The European chimney standards now describe chimneys and

flues by their temperature, pressure and resistance to corrosion,

condensation and fire. To identify the correct flue system, the

minimum flue specification is shown in the Technical Specification.

Existing chimneys are not covered by this system.

The chimney or flue system must comply with the rules in force,

and must be a minimum of 127mm (5") in diameter.

A 5" (127mm) liner must be used if fitting the appliance into an

existing brick built chimney.

Larger lined flues can work, but in some instances could cause

cold start flue problems resulting in nuisance shutdown. Lined flues

above 7" (175mm) are not recommended.

Suitable systems are:

a) Flexible liner which must be continuous from the

appliance spigot to the roof terminal.

b) Gazco Linerless kit.

UNDER NO CIRCUMSTANCES MUST THE LINERLESS KIT BE

USED WITH ANY INSTALLATION OTHER THAN AN EXISTING

MASONRY CHIMNEY WHICH HAS A MINIMUM DIAMETER OF

178mm (7”). THE CHIMNEY MUST BE SOUND AND CLEAN. IF

PREVIOUSLY USED FOR SOLID FUEL, IT MUST BE SWEPT

PRIOR TO PROCEEDING WITH THE INSTALLATION.

NOTE: If the Linerless kit is to be used, due care should be taken

to prevent condensation forming in the chimney. Do not fit the

Linerless Kit if the chimney is taller than 10 metres (external wall)

or 12 metres (internal wall).

The minimum flue height for the appliance must be 3 metres (10ft).

Any horizontal flue run from the rear outlet must not exceed 100mm

from the back of the appliance.

The chimney or flue must be free from any obstruction. Any damper

plates must be removed or secured in the fully open position, and

no restrictor plates fitted.

The chimney must be swept prior to the installation, but it need not

be swept if it can be seen the chimney is clean and unobstructed

throughout its entire length.

Steel Register

Plate with Clamp

that holds the Flex

Adapter

Flex Pipe Adapter

connects to stove

ue pipe

Stove Flue Pipe

running from the

stove to the Flex

Pipe Adapter

Stove

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gazco Loft Conventional Flue Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info