Bedienungsanleitung Gazco Loft Conventional Flue (Seite 13 von 52) (Englisch)

813398

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

FLUE OPTIONS

Consult the rules in force.

NOTE: This appliance does not normally require any additional

ventilation when installed in GB.

A range of Vitreous Enamel Gloss Black ue pipe is available

to compliment the appliance. Please contact your Gazco

retailer for further information.

GAS SUPPLY

THIS APPLIANCE IS INTENDED FOR USE ON A GAS

INSTALLATION WITH A GOVERNED METER.

Before installation, ensure that the local distribution conditions

(identication of the type of gas and pressure) and the adjustment

of the appliance are compatible.

Ensure the gas supply delivers the required amount of gas and is in

accordance with the rules in force.

You can use soft copper tubing on the installation and soft soldered

joints outside the appliance and below the re.

A factory tted isolation device is part of the inlet connection; no

further isolation device is required.

All supply gas pipes must be purged of any debris that may have

entered prior to connection to the appliance.

The gas supply must be installed in a way that does not restrict the

removal of the appliance for servicing and inspection.

VENTILATION

IMPORTANT: Ensure any national ventilation requirements are

taken into account during installation of the re.

UK ONLY:

The appliance has a nominal input not exceeding 7.0kW and does

not normally require any additional permanent ventilation.

FOR THE REPUBLIC OF IRELAND REFER TO THE RULES IN

FORCE FOR VENTILATION REQUIREMENTS.

APPLIANCE LOCATION

Once the position of the appliance has been decided:

Follow the instructions for securing the appliance on Page 20.

The non-combustible hearth must be at least 12mm thick, and

project a minimum of 50mm from the base of the appliance in all

directions.

The appliance is not suitable for installation against a combustible

wall. A combustible side wall must be a minimum of 200mm.

This appliance can be installed with an up and out ue (vertical wall

- horizontal ue) or with a vertical ue with roof termination (see

Site Requirements, Flue Options).

HEARTH INSTALLATION

(NOT APPLICABLE FOR BASE SECTION INSTALLATIONS

MODELS)

Building Regulations state this appliance must stand on a non-

combustible hearth that is at least 12mm thick and projects 50mm

minimum from the base of the appliance in all directions, however

Gazco recommend the hearth extends to the following dimensions,

see Diagram.

Dimensions A B C

All Models 781mm 498mm 12mm

BASE SECTION INSTALLATION

It is not necessary to site these products on a non-combustible

floor. However, for practical reasons, the floor should be flat and

solid to allow the appliance to be levelled and secured in place.

This appliance may be situated anywhere in the room, but due

consideration should be taken to ensure that it is sited within the

constraints of the allowable flue configuration.

DO NOT INSTALL APPLIANCE ON A CARPET.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gazco Loft Conventional Flue Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info