813406
34
Zoom out
Zoom in
Vorherige Seite
1/44
Nächste Seite
34
Servicing Instructions - Replacing Parts
5. Gas Valve
To change the gas valve:
5.1 Remove the Main Burner, see Section 2.
5.2 Release the gas inlet pipe, see Diagram 14, Arrow A.
B
A
C
D
14
5.3 Remove the thermocouple from the interrupter block.
5.4 Release the pilot pipe, see Diagram 14, Arrow B.
5.5 Release the gas outlet pipe, see Diagram 14 Arrow C.
5.6 Remove the eight wire loom, see Diagram 14, Arrow D.
5.7 Remove the two screws securing the valve to the support
bracket and withdraw the valve.
5.8 Replace in reverse order.
6. Magnetic Safety Device
To replace the magnetic safety valve:
6.1 Undo the thermocouple from the interrupter block and
remove the two interrupter leads.
6.2 Unscrew the interrupter block from the back of the valve.
6.3 Undo the silver magnetic valve retaining nut on the back of
the valve.
6.4 Gently tap out the mag valve.
6.5 Replace with a new unit.
6.6 Reassemble in reverse order ensuring that the interrupter
leads are connected correctly with the blue tag lead furthest
away from the gas valve body.
7. Control Box
7.1 Remove the Main Burner, see Section 2.
7.2 Remove the two thermocurrent cables by removing the two
screws, see Diagram 15.
7.3 Remove the ignition lead, see Diagram 15.
7.4 Remove the eight wire loom from the control box.
The control box can now be replaced.
When replacing the sealing plate on the rear of the control
cover use a suitable silicone sealant.
15
Pilot Burner 8 Wire Cable
Ignition Cable
Interrupter Block
Reset Button
GV60 Valve
Mains Adaptor
(Optional)
Thermocurrent
Cable SW
Thermocurrent
Cable TC
7.5 After replacing the control box you may need to reprogram
the handset.
Press and hold the reset button on the control box until
you hear two signals. After the second longer signal:
Release the reset button and within 20 seconds:
Press the DOWN button on the handset until you hear
two additional short signals confirming the new code is
set.
If there is a single long signal the code learning sequence
has failed or the wiring is incorrect.
34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Gazco Riva 2 F670 Balanced Flue wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info