Bedienungsanleitung Gazco riva Vision Large Conventional Flue (Seite 14 von 36) (Englisch)

813423

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Installation Instructions

1. Safety Precautions

1.1 For your own and other’s safety, you must install this

appliance according to local and national codes of practice.

Failure to install the appliance correctly could lead to

prosecution. Read these instructions before installing

and using this appliance.

1.2 These instructions must be left intact with the user.

1.3 Do not attempt to burn rubbish on this appliance.

1.4 Keep all plastic bags away from young children.

1.5 Do not place any object on or near to the appliance and

allow adequate clearance above the appliance.

IF THE APPLIANCE IS EXTINGUISHED OR GOES OUT

IN USE, WAIT 3 MINUTES BEFORE ATTEMPTING TO

RELIGHT THE APPLIANCE.

IMPORTANT: REFER TO DATA BADGE AND

TECHNICAL SPECIFICATION AT THE FRONT OF THE

MANUAL TO ENSURE THE APPLIANCE IS

CORRECTLY ADJUSTED FOR THE GAS TYPE AND

CATEGORY APPLICABLE IN THE COUNTRY OF USE.

FOR DETAILS OF CHANGING BETWEEN GAS TYPES

REFER TO SERVICING, SECTION 17, REPLACING

PARTS.

Unpacking

1.6 Remove the appliance from its packaging, and check that it

is complete and undamaged.

1.7 The glass lid is stored on top of the appliance. Remove and

store in a safe place.

Put the loose ceramic parts to one side so that they are not

damaged during installation.

2. Installation of the Appliance

IMPORTANT: THE OUTER PANELLING OF THE RIVA

VISION IS MADE FROM GLASS. USE CAUTION

WHEN INSTALLING, REMOVING AND STORING AS

THE COMPONENTS ARE FRAGILE AND COULD

BREAK UNLESS HANDLED CAREFULLY.

Please note: As an optional extra Gazco can provide

a mains adapter to supply constant power to the

appliance control box instead of the battery pack.

If installing an appliance with the adapter make

provision for a mains power socket within 1.5m of

the control box and follow the instructions provided.

2.1 Remove the front from the appliance by lifting clear of the

slotted hooks, see Diagram 1.

Use the hex key provided to release the window locks

moving each from shut to open towards the outer edge of

the glass door, see Diagram 2.

2.2 Remove the box from the appliance and store safely as it

contains the remote control and fuel effects.

2.3 Remove all the enamel or vermiculite liners where

necessary.

2.4 To access the controls and pressure test point:

Remove the glass front, liners, burner and splitter plate,

refer to Servicing, Replacing Parts, Section 3 - 7.

2.5 Check the pull of the flue system by applying a lighted

smoke pellet to the flue system opening If there is a definite

flow into the chimney, proceed with the installation. If not,

warm the chimney for a few minutes.

IF THERE IS STILL NO DEFINITE FLOW, THE FLUE MAY

REQUIRE ATTENTION - SEEK EXPERT ADVICE

A drilling template is supplied in order to locate the

fixing plates.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gazco riva Vision Large Conventional Flue Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info