Bedienungsanleitung Gazco Riva Vision Large MK1 Series Balanced Flue Instructions (Seite 5 von 40) (Englisch)

813414

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

User Instructions

2. Operating the Appliance

2.1 The appliance has 4 flame settings:

1. High.

2. Medium.

3. Low.

4. Standby (Pilot only).

2.2 Both touch pad and handset allow you to manually switch

between flame settings.

2.3 The Thermostatic handset also allows to set the appliance

to automatically regulate the room temperature.

On/Off

Button

3 x Selection

Buttons

Before using the remote control:

2.4 If there is no display on the LCD screen press any key.

2.5 When first powered, the handset displays the OFF screen.

The handset may be locked as indicated by the padlock

symbol ( ), see Diagram 2.

NOTE: To select a function from the options displayed at the

bottom of the screen press the button directly below the

desired function.

2.6 To unlock the handset select Unlock followed by OK - the

symbol will change to an open padlock ( ).

2.7 There are 3 different modes available for controlling and

operating the appliance:

1. Manual Mode - See Page 6.

2. Automatic Mode - See Page 6.

3. Program Mode - See Page 7.

When a command from the handset is received a beep will

sound and the LED on the handset will briefly illuminate.

NOTE: The LED flashes every 4 seconds to show that it is

communicating with the appliance. After each command has

been accepted the LED will cease flashing until the

command has been carried out. Wait until the LED resumes

flashing before giving another command.

Advanced Controls

2.8 The thermostatic remote control handset has been pre-set

as follows:

a) Thermostat mode - the appliance will alter automatically

to achieve and maintain a desired room temperature in Auto

(Fixed Temp) or Program mode.

b) Gap temperature set at 2˚C - in Auto or Program mode

the appliance will automatically ignite if the room

temperature falls 2˚C below the fixed temperature.

c) Program mode enabled - this allows one of three

temperatures (Night temperature, Comfort temperature or

Off) to be set for each hour of the day on a daily or weekly

cycle.

d) Soft start enabled - in Auto or Program mode there is a

10 second delay between flame settings when more than

one change of setting is required (i.e. from High to Low).

e) Sounder ON - the appliance will beep to confirm that it

has received a command from the handset or touch pad.

f) Safety Temperature pre-set at 40˚C - the appliance will

automatically switch off if the room temperature (as

displayed on the handset) exceeds 40˚C.

NOTE: If the Safety Temperature is exceeded the appliance

can not be turned on again until the room temperature has

dropped below the safety temperature.

2.9 The LCD screen displays the following information, see

Diagram 3.

1) Time (24 hr clock)

2) Signal strength (between handset and appliance)

3) Selected Setting - set fixed temperature (in degrees)

when in Auto mode (small number)

4) Current room temperature (large number)

5) Button function

6) Child lock status (shown by open or closed padlock)

7) Current flame status (Low, Med, High)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gazco Riva Vision Large MK1 Series Balanced Flue Instructions Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info