Bedienungsanleitung Gazco Riva Vision Large MK1 Series Conventional Flue (Seite 23 von 36) (Englisch)

813415

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Commissioning

1. Commissioning

1.1 Check the flame picture, log/pebble layout.

1.2 Check the gas pressure.

1.3 Close all door and windows in the room.

1.4 Ignite the Studio and operate on maximum for 5 minutes.

1.5 Position a lighted smoke match just inside the draught

diverter opening and check all smoke is drawn in along the

opening.

If there is any doubt:

1.6 Run the appliance for a further 10 minutes and repeat the

test, see Diagram 1.

1.7 Complete the Commissioning Checklist at the front of this

manual covering:

— Flue checks

— Gas checks

— Log/fuel effect layout - flame picture

For working pressure test, use the access panel at the gas

connection ensuring the burner is in position. Refer to

Replacement Parts, Section 18.

1.8 Upon completion of the commissioning and testing of the

installation and correct operation of the appliance, the

installer must instruct the user how to operate the appliance.

1.9 Guide the user through the User Instructions paying

particular attention to:

a) Regular servicing (Section 12 of the User Instructions).

b) Ventilation (Section 13 of the User Instructions) - point out

the ventilation positions where applicable.

c) Hot surfaces (Section 15 of the User Instructions).

d) How the appliance works with the touch pad control

(Section 5 of the User Instructions).

e) How the appliance works with the remote control handset

and the modes of operation (Section 2 of the User

Instructions).

f) How to change settings in the auto mode and program

modes of operation.

g) What to do if the appliance fails to operate (Section 16 of

the User Instructions).

If there are any extractor fans in the room or adjacent

rooms, the test must be repeated with the fans running on

maximum.

IF SPILLAGE PERSISTS, DISCONNECT THE APPLIANCE

ANDSEEKEXPERTADVICE.

For future reference, record the installation details on the

Commissioning Sheet on page 3.

2. Pairing the appliance

To access the control panel in order to pair the

appliance it will be necessary to remove the Main

Control Assembly, see Servicing Section 4.

If there is no communication between the remote control

and the appliance after replacing the control box or the

handset, it will be necessary to pair the two together.

Before starting the pairing process ensure the handset

is programmed to Channel 'C' see Section 3.

2.2 Ensure batteries are fitted and working in the handset.

2.3 Check all leads and cables are connected correctly.

2.4 Ensure the handset is unlocked. To unlock the handset

select Unlock followed by OK - the symbol will change to

( ).

2.5 Press the ON/OFF button (�) on the handset and keep it

depressed until the screen changes to the configuration

menu. This may take up to 30 seconds and the screen may

go blank before changing to the configuration screen.

2.6 When the configuration menu screen appears change the

Pairing option to ON using the Change button.

2.7 Within 20 seconds press the yellow button on the control

unit repeatedly until a single beep is heard confirming the

pairing operation has been successful, see Diagram 1. This

may be easier using a pencil, ball point pen or similar.

Remote Handset

Pairing Button

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gazco Riva Vision Large MK1 Series Conventional Flue Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info