Bedienungsanleitung Gazco Stockton - Electric Range (Seite 11 von 80) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Norwegisch)

813467

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

INSTALLATION

GENERAL

TOOLS REQUIRED

1 X Screwdriver

UNPACKING THE APPLIANCE

WARNING! DO NOT use this appliance if any part has been

exposed to water.

Immediately call a qualified service technician to inspect and to

replace any part of the electrical system if necessary.

Open the packaging carefully and remove the polystyrene.

Remove and discard the plastic bag.

Keep plastic wrapping away from children.

Be responsible when handling the packing materials.

Check all parts and accessories are removed before disposing of

any packaging.

If necessary keep the original packaging for future transport and/

or storage.

Test the appliance before installation.

This appliance is heavy and does not require

anchoring to the hearth or floor, but in certain

circumstances the appliance can become

unstable e.g. when leaning on the appliance. If

this is likely, secure the appliance to the hearth

or floor with suitably strong fixings.

LOCATING THE APPLIANCE

The appliance may be installed virtually anywhere in your home.

However, when choosing a location ensure that the general

instructions are followed.

For best results, install out of direct sunlight.

If the power cord is damaged contact your Gazco retailer for a

replacement. Only use genuine Gazco parts on this appliance.

The appliance should be located close to a suitable mains socket

to enable connection.

The electrical socket must be easily accessible to allow

disconnection when the appliance is fitted.

This appliance must stand on a clean, level, firm surface.

Do not stand the appliance on a carpet. Ensure that furniture,

curtains etc. are positioned no closer than 1m and the appliance

stands on a surface that can withstand temperatures of 90°C for

prolonged periods. Do not allow rugs to be placed within 500mm of

the front of the appliance.

Ensure that curtains and furniture are not positioned close to the

chosen position, as this would create a potential fire hazard or

block the heater outlet ducts.

WARNING! KEEP ANY COMBUSTIBLE MATERIALS AT LEAST

1M FROM THE FRONT AND SIDES OF THE APPLIANCE.

ALL INGLENOOK FIREPLACE OPENINGS:

For all models the dimensions required for an inglenook installation

can be calculated by adding 225mm (9”) to the height of the

appliance and 150mm (6”) to each side. An additional 50mm (2”)

must be added to the depth to provide adequate space behind the

appliance.

SERVICING AND SUPPORT

Servicing and Support

To keep your appliance looking and performing at its best, it must

be serviced annually. This service must be undertaken by a suitably

qualified individual and your retailer can organise this for you.

Alternatively, Gazco offer a manufacturers premium service with our

friendly team of qualified engineers which can be booked at www.

gazco.com/support

SERVICING REQUIREMENTS

DURING SERVICING OF THIS APPLIANCE IT MAY BE

NECESSARY TO CUT CABLE TIES IN ORDER TO

ACCESS AND REMOVE SOME OF THE PARTS.

THESE MUST BE REPLACED WHEN

REASSEMBLING THE APPLIANCE.

THIS APPLIANCE MUST ONLY BE SERVICED BY A SUITABLY

QUALIFIED PERSON.

BEFORE UNDERTAKING ANY WORK ON THE APPLIANCE:

SWITCH OFF THE APPLIANCE AND ISOLATE THE POWER

SUPPLY ENSURING THERE IS NO POWER TO THE APPLIANCE.

Wait for at least 10 minutes until the appliance has cooled down.

Remote Handset Battery Replacement

Replace with 2 AAA batteries. Make sure the batteries are installed

correctly in the remote control.

NOTE: The remote control has a Battery Status

indicator (top right corner), after an extended

period of displaying empty the LED screen will

cease to function despite the handset still being

able to send commands.

Replace the batteries to restore display.

Maintenance of Motors

The motor used on the flame effect is pre-lubricated for extended

bearing life and requires no further lubrication. However, periodic

cleaning/vacuuming of the heater unit is recommended.

Resetting the Thermal Cutout Switch

The appliance is fitted with an Electronic Safety Control (E.S.). This

is a safety device which switches off the fire if, the appliance

overheats for any reason e.g. when covered.

If the heater stops operating whilst the flame effect continues

normally, this indicates that the E.S. Control is in operation.

The E.S. Control can only be re-set after the appliance has cooled

down.

To re-set the E.S:

Switch off the appliance (Manual On/Off switch) and leave for

approximately 120 minutes.

Remove any obstruction to the fan heater outlet or other internal

parts.

Switch on appliance and the E.S. Control will re-set. Ensure that

the appliance is functioning correctly. If the E.S. Control operates

again, the appliance should be checked by a competent

Electrician.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gazco Stockton - Electric Range Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info