Bedienungsanleitung Gazco Studio Freestanding Conventional Flue (Seite 12 von 48) (Englisch)

813413

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

1. Flue & Chimney Requirements

WHEN INSTALLING A FLUE SYSTEM PLEASE REFER

TO THE MANUFACTURER’S INSTRUCTIONS.

The European chimney standards now describe chimneys

and ues by their temperature, pressure and resistance

to corrosion, condensation and re. To identify the correct

ue system, the minimum ue specication is shown in the

Technical Specication. Existing chimneys are not covered

by this system.

The ue must be installed in accordance with all local and

national regulations and the current rules in force:

1.1 A exible liner must be continuous from the appliance spigot

to the roof terminal.

1.2 The minimum effective height of the ue must be 3m (10').

1.3 The ue must be free from any obstruction.

1.4 Any damper plates must be removed or secured in the fully

open position and no restrictor plates tted.

1.5 The chimney should be swept immediately before installing

the appliance, but it need not be swept if you can see the

chimney is clean and free from obstruction throughout.

2. Flue Options

Top Exit only - Twin Wall Rigid 127mm (5”)

A range of Vitreous Enamel Gloss Black ue pipe is

available to compliment the appliance. Please contact

your Gazco retailer for further information.

3. Gas Supply

This appliance is intended for use on a gas installation with a

governed meter.

3.1 Make sure local distribution conditions (identication of

the type of gas and pressure) and the adjustment of the

appliance are compatible before installation.

3.2 Ensure the gas supply delivers the required amount of gas

and is in accordance with the rules in force.

3.3 Soft copper tubing can be used on the installation and soft

soldered joints outside the appliance and below the rebed.

3.4 A factory tted isolation device is part of the inlet connection;

no further isolation device is required.

3.5 All supply gas pipes must be purged of any debris that may

have entered prior to connection to the appliance.

3.6 The gas supply enters through the silicone panel located

beneath the control access panel at the base of the rebox.

Slit with a sharp knife before passing the supply pipe

through.

3.7 The gas supply must be installed in a way that does not

restrict the removal of the appliance for servicing and

inspection.

4. Ventilation

IMPORTANT: Ensure any national ventilation

requirements are taken into account during installation

of the appliance.

UK ONLY:

The Studio 1 has a nominal input not exceeding 7.0kW

and does not normally require any additional permanent

ventilation.

The Studio 2 must have permanent ventilation with a

minimum open area of 4cm2.

If however, spillage is detected when commissioning the

appliance, there may be insufcient natural ventilation and

additional ventilation may be required.

FOR THE REPUBLIC OF IRELAND REFER TO THE

RULES IN FORCE FOR VENTILATION REQUIREMENTS.

5. Appliance Location

5.1 This appliance has been designed to stand on a designated

bench or plinth.

5.2 For practical reasons, the oor should be at and solid to

allow the appliance to be levelled and secured in place.

5.3 This appliance may be situated anywhere in the room, but

due consideration should be taken to ensure that it is sited

within the constraints of the allowable ue conguration.

5.4 If the appliance is to be sited against a combustible wall, a

clearance of 50mm should be allowed between the wall and

the rear of the appliance.

5.5 This appliance must not be installed in a room that contains

a bath or shower.

5.6 Installations on a Bench or Plinth do not need a non-

combustible oor but the appliance must not be tted on a

carpet. Use a solid oor.

5.7 Installations on a Bench or Plinth do not require xing to the

oor.

5.8 To secure the appliance to the Bench or Plinth follow the

instructions on Page 15.

Installation Instructions

Site Requirements

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gazco Studio Freestanding Conventional Flue Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info